manualshive.com logo in svg

Vertical Technologies DeltaQuad Evo, Operation Manual

Share
Download
Vertical Technologies DeltaQuad Evo Operation Manual Download Page 122

In fixed-wing mode

Not activated

Shutting down & charging the controller

The DeltaQuad Controller can operate continuously for approximately 6 hours. If more operation time is 
required, the controller can be charged during operation.

To charge the controller, open the rubber cover between the antennas and attach the provided USB charger 
to the USB-C port. The controller requires high-voltage charging. Standard USB chargers or USB sockets 
from laptops are not always capable of providing high voltage, but they will extend the battery life of the 
controller.

To shut down the controller, press and hold the power button until the shutdown menu appears. Select 
"Power off" to shut down the controller.

Payload Drop Mechanism

If your DeltaQuad is equipped with a Payload Drop Mechanism (PDM) you may use the following 
instructions to operate the PDM. Please note that dropping payloads from a UAV might require special 
permits. Please check with your local authorities before using the payload drop mechanism. Never operate 
the PDM near people, roads or property.

Mechanical

The PDM consists of a payload bay with 2 payload doors that are operated by servo motors. The Servo 
motors are attached to the payload doors with steel rods. Never operate the payload doors when they are 
obstructed as this might damage the system..

Payload bay dimensions

10 cm x 15 cm x 9 cm

Summary of Contents for DeltaQuad Evo































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands