Vermont Castings RHE25 Installation Instructions & Homeowner'S Manual Download

Page: 37 / 38

10000836

Vermont Castings, Majestic Products RHE Natural Vent Insert

Extension
Knobs

KT204a

Fig. 64 Install the knob extensions. (RN/RP models Only)

KT212a

Fig. 68 Attach magnets and brass trim to the steel frame.

KT210

Fig. 66 Hang the window grille or the steel frame onto the
lower tabs of the hanging brackets.

Hanging Bracket

KT209a

Fig. 65 Hanging bracket alignment.

KT211a

Fig. 67 Engage the slots in the upper grille top louvre with
the upper tabs of the hanging brackets.

HE42BTKP Trim Replacement Parts

IMPORTANT: Only trim panel assemblies approved
by Vermont Castings, Majestic Products can be
used on these products.

ALL repair parts will be available from your local dealer.

When ordering, always give the following information:
Model and serial number, part description with finish
and part number.

Vermont Castings, Majestic Products reserves the right to make
changes in design, materials, specifications, prices and discontinue
colors and products at any time, without notice.

Key

Description

HE42BTKP

Trim Window Top & Bottom
(w/magnets)

57576

Top Louvre Assembly (Metallic Black)

10000932

Bottom Louvre Assembly
(Metallic Black)

10000933

Control Door (Metallic Black)

10000934

Plate Decorative Bottom

57551

Hinge

52356

Glass Side

57405

Glass Front

57406

Ceramic Refractory Bay

10000854

Extension Knob On/Off
(only for RN/RP valves)

55163

Extension Knob Hi/Lo
(only for RN/RP valves)

55162

Bracket Hanging Bay Window

1409129

Bracket Extension Rheostat

1409146

Extension Knob Hi/Lo
(Honeywell Valve)

20000006

Extension Knob On/Off
(Honeywell Valve)

20000007

Extension Knob Piezo Ignitor
(Honeywell Valve)

20001427

Hardware Package (Not Shown)

10000928

Summary of Contents for RHE25







































Search results

Summary of Contents for RHE25

Reviews:

Related manuals for RHE25

Brands by name

Popular brands

Vermont Castings RHE25, Installation Instructions & Homeowner'S Manual

Search results

Summary of Contents for RHE25

Reviews:

Related manuals for RHE25

Brands by name

Popular brands