background image

10

Encore Multi-Fuel Heater

2000971

in section 2 of document j, all installations must 
comply with these requirements or with the relevant 
National or local building standards.

Clearances to timber framed (studded) walls are in-
cluded below. There are no specific minimum clearanc-
es to solid noncombustible surfaces (e.g. the sides and 
rear of Inglenook fire openings constructed from solid 
masonry) other than to allow safe access to the controls 
of the stove. For this reason minimum side clearances 
of 125 mm, and a minimum rear clearance of 50 mm 
are recommended.

Summary of Clearances

Minimum recommended side clearances to non-
combustible surfaces 125 mm (5”).
Minimum recommended rear clearance to noncom-
bustible surfaces 50 mm (2”).
NotE:

 The minimum thickness of solid noncombus-

tible materials is specified in section 2 of Document ‘J’, 
in relation to the clearance of the appliance from the 
surface. As a general rule, the thickness of solid non-
combustible material forming the recess of a fireplace is 
a minimum of 200 mm.

Minimum rear clearance from combustible walls 
(e.g. timber framed or studded walls) 840 mm (33”) 
measured from the rear edge of the stove top. (Fig. 
12, b)

ST486a

Defiant EU

Clearance

Diagrams

10/06

A

B

ST486a

Fig. 12

  Minimum clearances.

Minimum side clearance from combustible walls 
610 mm (24”) measured from the side edge of the 
stove top. (Fig. 12, a)
Minimum distance from stove to movable combus-
tible materials (e.g. furniture, drying clothes, etc.) 
1220 mm (48”).

Connecting Flue pipe - Clearances

Single wall connecting fluepipes can reach extremely 
high temperatures; therefore, clearances from the con-
necting fluepipe (chimney connector) must comply with 
the requirements of Part J of Building Regulations 2000 
(Combustion Appliances and Fuel Storage Systems). 
This can be achieved by following the recommenda-
tions of Approved Document ‘J’. These are as shown in 
Figure 13.

34
FLUEPIPECLEARANCES

D

at least 
3 x D

Elevation 

without 

Shield

Elevation 

with Shield

at least 

3 x D

at least 

1.5 x D

at least 1.5 

x D

plan without 

Shield

plan with 

Shield

Air space of at least 12 mm 

between noncombustible shield 

and combustible material

Fluepipe

at least 

1.5 x D

at least 

1.5 x D

at least 3 x D

D

at least 

1.5 x D

ST911

Fig. 13

  Connecting fluepipe clearances.

Summary of Contents for Encore 2547CE





























Reviews: