background image

33

Omni 3200M Installation Guide

To be certain of the number of devices that may be connected to the line, as 
determined by the total RENs, contact the telephone company to determine the 
maximum REN for the calling area.
An FCC-compliant telephone line cord and modular plug is provided with this 
equipment. This equipment is designed to be connected to the telephone network 
or premises wiring using a compatible modular jack which is FCC Part 68 
compliant.
If this equipment causes harm to the telephone network, the telephone company 
will notify you in advance that temporary discontinuance of service may be 
required. However, if advance notice is not practical, the telephone company 
will notify the customer as soon as possible. Also, you will be advised of your 
right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, 
operations, or procedures that could affect the operation of this equipment. If 
this happens, the telephone company will provide advance notice so that you 
can make the necessary modifications to maintain uninterrupted service.
No repairs may be performed by the user. If trouble is experienced with this 
equipment, contact your VeriFone representative or service provider. Or, call the 
VeriFone Service and Support Group at 1-800-834-9133 inside the U.S. for 
information and instructions. If the trouble is causing harm to the telephone 
network, the telephone company may request that you remove this equipment 
from the network until the problem is solved.
This terminal cannot be used on public coin service provided by the telephone 
company. Connection to Party Line Service is subject to state tariffs. (Contact 
the state public utility commission, public service commission, or corporation 
commission for information.)
It is recommended that the customer install an AC surge arrestor in the AC 
outlet to which this device is connected. This is to avoid damage to the 
equipment caused by local lightning strikes and other electrical surges.

FCC Part 90

This device contains a radio transceiver module, (FCC ID number is on the 
bottom of the terminal), operating under Part 90 of the FCC rules in a licensed 
part of the radio spectrum. Service or repairs to the radio portion of this device 
must be performed by qualified personnel. Any unauthorized modification to the 
radio module, shielding, or antenna may void the user's authority to operate this 
device. 

Summary of Contents for Omni 3200M










































Reviews: