background image

Verasys® 32 Point 24 VAC Application Controller Installation Instructions

22

Cable and Wire Length Guidelines

Table 6 defines cable length guidelines for the various wire sizes for wiring low-voltage (<30 V) input and output 
wiring. 

BINARY - RELAY 
(Outputs)
(SPDT)

OUTn NO
OUTn NC

Normal Open and Normal Closed 
Contact

Connects OCOM to OUT NO when 
activated and disconnects OCOM to 
OUT_NC

UL 916

240 VAC 5A resistive, 1.9 FLA/11/4 
LRA, D300 pilot duty, +70°C (158°F), 
30K cycles

EN 60730

240 VAC 3A resistive, 3A inductive, 
Cos(phi) = 0.6, -20° to 70°C 
(-4 to 158°F), 100K cycles

The RELAY output terminals can 
accommodate the following maximum 
wire sizes:
Two wires per terminal: 1.5 mm

2

 

(16 AWG) maximum

or

One wire per terminal: 2.5 mm

2

 

maximum (12 AWG or 2–16 AWG)

Note:

You must determine the 

required 

wire size for the high-voltage 

(>30 V) terminals according to relay 
ratings, the applied load, and the 
local, national, or regional electrical 
codes.

OCOMn

Relay Common

Isolated from all other terminal 
commons, including other Relay 
Commons.

Note:

Reference all relay commons 

to the same pole of the supply circuit.

PWM Output

OUT5 PWM

PWM Output

User selectable PWM output voltage 
(5V, 12V default and 15V), 10 mA 
continuous current, 100 Hz frequency

See Guideline 

A

 in Table 6.

PWM COM

PWM Common

PWM return for the single PWM 
channel on the controller.

See Guideline 

A

 in Table 6.

1.

See Table 6 to determine wire size and cable lengths for cables.

Table 6:  Cable Length Guidelines for Wire Sizes for Low-Voltage (<30 V) Inputs and Outputs (Part 1 of 2)

Guidelines

Wire Size/Gauge and 
Type

Maximum Cable 
Length and Type

Assumptions

A

1.5 mm

(32 AWG) 

stranded copper

457 m (1,500 ft) twisted 
wire

100 mV maximum voltage drop
Depending on the cable and the connected input or 
output device, you may have to define an offset in the 
setup software for the input or output point.

0.8 mm

2

 (20 AWG) 

stranded copper

297 m (975 ft) twisted 
wire

0.6 mm

2

 (22 AWG) 

stranded copper

323 m (1060 ft) twisted 
wire

N/A (24 AWG) 
stranded copper

107 m (350 ft) twisted 
wire

Table 5:  Controller Terminal Blocks, Functions, Ratings, Requirements, and Cables (Part 4 of 4)

Terminal Block
Label

Terminal Label

Function, Ratings, Requirements

Determine Wire Size and Maximum 
Cable Length

1

Summary of Contents for LC-VAC300 0 Series





























Reviews: