Velleman SPBS10, User Manual

Page: 6 / 38

31.07.2014
6
*%)"*' %-) < =
•
Refer to the vehicle installation drawings or experienced advice when de
of the control unit. The control unit should not be close to potential sour
e.g. cable bundles, exhaust pipe….
•
Make sure the power cables of the control unit are easily accessible.
•
Use the included double sided adhesive tape to fix the control unit to the
- 0'$4 &%-)
•
The display unit should be mounted on the dashboard with the included
Make sure that the display is readable under all conditions.
•
Guide the cable towards the CU.
•
Plug the connector into the CU. The connector fits only one way, do not
$2'-%>?,*%%!,)-*%
•
Every sensor cable has a letter written on it.
•
Plug each sensor cable into the corresponding port on the CU.
*%%!,)-%> 0*5!"
•
The CU gets power from the reverse light circuit of the vehicle. Use the
and the included cable clips to make the connections.
•
Locate the +12V power cable of the reverse light circuit and guide it thr
•
Insert the red cable of the CU power cable in that cable clip and press th
clip tightly. Close the cable clip.
•
Locate the GND cable of the reverse light circuit and guide it through a c
•
Insert the black cable of the CU power cable in that cable clip and press
clip tightly. Close the cable clip.
•
Connect the power cable to the CU.
@( 0!"$)-*%
$"%-%> #*+!
•
Following is an overview of the warning zones.
$"%-%> A*%! - )$%,! <#= &+-2'!
Danger zone D ≤ 0.2 Bi.........
Caution zone
0.3 < D ≤ 0.4 Bi.Bi.
0.5 < D ≤ 0.9 Bi..Bi.
Safety zone
1.0 < D ≤ 1.5 Bi..…Bi…
1.6 < D ≤ 2.0 <
!5$"! *. )/! 2'-%+ A*%! 2!/-%+ )/! 1!/-,'!B 2 )$,'! '*,$)!
A*%! 5-'' 2! +!)!,)!+B /! 2'-%+ A*%! 2!/-%+ )/! 1!/-,'!
•
When an obstacle is detected in a warning zone, visual and audible warn
display unit.
•
Visual warnings are given by flashing of the display indicator C D of the s
the obstacle, as well as a numeric display of the distance in meter C D
when an obstacle is detected by sensor or , the left indicator will f
by sensor or , the right indicator will flash.
•
The time interval between the beeps is an indication of the distance to t
shorter the interval, the closer the obstacle. See the table below for an o
•
When multiple obstacles are detected, the display indicators of the sens
the distance to the obstacle located inside the highest priority warning z
accompanying audible warnings are given.
•
The audible warnings can be disabled with the switch C D on the LCD.
©Velleman nv
n determining the location
sources of interference,
the cars’ interior.
ded mounting bracket.
not force.
the red/black power cable
through a cable clip.
ss the metal part of the
a cable clip.
ess the metal part of the
2'! ->%$'
.............
i.Bi.Bi
..Bi..Bi
…Bi…..Bi
<
,$)!+ -% -+! )/! 2'-%+
-,'! - 7 ,#(
arnings are given on the
he sensor(s) that detected
D and a bar graph C D .
ill flash, when detected
to the obstacle. The
an overview.
ensors will flash, but only
ng zone and the