background image

1

  Introduction

This manual tells you how to install the Veeder-Root Groundwater Sensor, Part No. 794380-62X. The manual 
assumes all preliminary site preparation is completed, and that field wiring from the monitor to the sensor junction 
box is in place.

For new installations, or if site preparation is necessary, refer to the appropriate Veeder-Root Site Preparation and 
Installation Instructions or contact your Veeder-Root representative for assistance.

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and setup the 
equipment discussed in this manual:

Installer Certification (Level 1):

 Contractors holding valid Installer Certification are approved to perform wiring 

and conduit routing; equipment mounting; probe, sensor and carbon canister vapor polisher installation; wireless 
equipment installation; tank and line preparation; and line leak detector installation.

Technician Certification (Level 2/3):

 Contractors holding valid Technician Certifications are approved to 

perform installation checkout, startup, programming and operations training, system tests, troubleshooting and 
servicing for all Veeder-Root Series Tank Monitoring Systems, including Line Leak Detection. In addition, 
Contractors with the following sub-certification designations are approved to perform installation checkout, startup, 
programming, system tests, troubleshooting, service techniques and operations training on the designated system. 

• Wireless  2
• Tall Tank

Warranty Registrations 

may only be submitted by selected Distributors.

Product Marking Information

RELATED DOCUMENTS

Documents Required to Install Equipment

This intrinsically safe apparatus is only for use as part of a Veeder-Root Automatic Tank Gauging System (ATG 
Console with probes and sensors). To install intrinsically safe apparatus, use the specific control drawing that 
appears on the nameplate of the applicable associated apparatus (ATG Console):

The control drawings contain information related to the correct installation of the overall intrinsically Safe System. 
This includes information such as maximum number of apparatus, specific apparatus allowed in the system, 
maximum cable lengths, references to codes, proper grounding and so on. Control drawings can be found on the 
accompanying Compact Disk (TECH DOCS CD) or on the internet at veeder.com under SUPPORT; VR 
TECHNICAL DOCUMENTS; DRAWINGS.

Equipment

UL/cUL Control Drawing

Document No.

Associated Apparatus

TLS-450/8600

331940-008

TLS-350, TLS-350R

331940-011

TLS4/8601

331940-018

Summary of Contents for TLS-450/8600











Reviews: