background image

  Introduction

This manual provides instructions to install, setup, and operate the components of Veeder-Root Pressure 
Management Control (PMC) equipment. The PMC feature is an option for the TLS console platform, and as such, 
many of the installation/setup/operation instructions for non-PMC specific tasks are covered in TLS-3XX supplied 
literature. Do not use this manual when PMC is installed with ISD. Use the ISD Setup & Operation Manual, 
577021-800.

Site Requirements

Below are the requirements for all PMC installations:

• V-R TLS-350R/EMC w/BIR, TLS-350 Plus/EMC Enhanced, TLS-350/EMC and ProMax consoles with ECPU2 

- install as per TLS-3XX Site Prep manual, setup following instructions in TLS-3XX System Setup Manual.

• A flash memory board (NVMEM203) for PMC software storage - installed on the ECPU2 board in place of the 

console’s 1/2 Meg RAM board - install as per TLS-350 Series Board and Software Replacement Manual, no 
setup required.

• Smart Sensor Module and Vapor Pressure Sensor. Install and connect following instructions in the Vapor 

Pressure Sensor installation Guide.

• Mod Bus module connected to a hydrocarbon sensor module installed according to processor manufacturers 

specifications.

• An RS-232 Port will be available for use by contractor or government inspectors.

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and setup the 
equipment discussed in this manual:

Level 1

Contractors holding valid Level 1 Certification are approved to perform wiring and 
conduit routing, equipment mounting, probe and sensor installation, tank and line 
preparation, and line leak detector installation.

Level 2/3 or 4

Contractors holding valid Level 2, 3 or 4 Certifications are approved to perform 
installation checkout, startup, programming and operations training, troubleshooting 
and servicing for all Veeder-Root Tank Monitoring Systems, including Line Leak 
Detection and associated accessories.

ISD/PMC

This course of training includes In-Stations Diagnostics/Pressure Management Control 
(ISD/PMC) installation checkout, startup, programming, and operations training. It also 
includes troubleshooting and service techniques for the Veeder-Root In-Station 
Diagnostics system. A current level 2/3 or 4 certification is a prerequisite for the ISD/
PMC course. After successful completion of this course the contractor will receive a 
certificate as well as a Veeder-Root ISD/PMC contractor certification card.

Warranty Registrations

 

may only be submitted by selected Distributors.

Section 16

Pressure Management Control

16-1

Summary of Contents for TLS-350R

























Reviews: