background image

  Setup

Introduction

This section describes how to perform PMC setup using the TLS console’s front panel buttons and display. The 
procedures in this manual follow standard TLS console setup programming input, i.e., keypad/display interaction. If 
necessary, refer to Section 2 of the TLS-3XX System Setup manual (P/N 576013-623) to review entering data via 
the front panel keypads.

All PMC-related equipment must be installed in the site and connected to the TLS console prior to beginning the 
setups covered in this section. As with all TLS connections, you cannot change sensor wiring or module slots after 
programming or the console may not operate properly. Reference the section entitled “Connecting Probe/Sensor 
Wiring to Consoles” in the TLS-3XX Site Prep and Installation manual (P/N 576013-879) for rewiring precautions.

Smart Sensor Setup

The Smart Sensor Interface Module is installed in the Intrinsically-Safe bay of the TLS console. This module 
monitors the Vapor Pressure Sensor. Figure 2 diagrams the Smart Sensor setup procedure.

Figure 2.  Smart Sensor Setup

SS CONFIG - MODULE  1
SLOT X - X  X  X  X  X  X  X  X

S

isd\pmc-5.eps

ENTER SMARTSENSOR LABEL
sX:

S1: SELECT SS CATEGORY
UNKNOWN

C

C

E

S

E

S

E

S

P

F

SMARTSENSOR SETUP
PRESS <STEP> TO CONTINUE

SETUP MODE

PRESS <FUNCTION> TO CONT

M

P

 

C

C

C

F

P

S

T

Change

E

Enter

Function

Print

M

Mode

Step

Tank/Sensor

Key press
sequence

Repress until
desired message
appears in display

Key Legend

1

2

Select sensor category
(e.g., Vapor Pressure Sensor)

Press this button and select type. 
Note: User can only change assigment 
if device has not identified itself. If 
actual device disagrees with assigned 
type, actual type overrides assigned 
type.

The first of the installed SS modules 
appears in this display. If this is not the 
module to which the Vapor Pressure 
Sensor (VPS) is connected, press the 
Tank/Sensor button to select another 
SS module. 

Press once and the first position blinks. If 
the VPS is connected to the first position 
of the SS module, press this button again 
and the X changes to a 1.

Press this button and 
the X changes to the 
number of the VPS 
connection (2-8).

Prints out a copy of the 
SmartSensor Setup.
See example at right.

Press this button and enter 
a label for the sensor, e.g., 
VPS: FP1&2.

T

Press this button to 
change to another sensor.

If the VPS is connected to a position other 
than the first, continue to press this button 
until the VPS connected position blinks.

SMARTSENSOR SETUP

---------------------- 

S01:VP SENSOR

CATEGORY VAPOR PRESSURE

Section 16

Pressure Management Control

16-5

Summary of Contents for TLS-350R

























Reviews: