background image

Notice

Veeder-Root makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranties of

 

merchantability and fitness for a particular purpose.

Veeder-Root shall not be liable for errors contained herein or for incidental or consequential damages

 

in connection with the furnishing, performance, or use of this publication.

Veeder-Root reserves the right to change system options or features, or the information contained in this publication.
This publication contains proprietary information which is protected by copyright. All rights reserved. No part of this publication

 

may be photocopied, reproduced, or translated to another language without the prior written consent of Veeder-Root.
Contact Red Jacket Technical Support for additional troubleshooting information at 800-323-1799.

DAMAGE GOODS/LOST EQUIPMENT

Thoroughly  examine all components and units  as  soon  as  they  are  received.  If any  cartons  are  damaged or  missing,  write  a

 

complete and detailed description of the damage or shortage on the face of the freight bill. The carrier's agent must verify the

 

inspection and sign the description. Refuse only the damaged product, not the entire shipment.
VR must be notified of any damages and/or shortages within 30 days of receipt of the shipment, as stated in our Terms and

 

Conditions.

VEEDER-ROOT’S PREFERRED CARRIER

1. Fax Bill of Lading to V/R Customer Service at 800-234-5350.
2. Call V/R Customer Service at 800-873-3313 with the specific part numbers and quantities that were received damaged or

 

lost.

3. VR will file the claim with the carrier and replace the damaged/missing product at no charge to the customer. Customer

 

Service will work with production facility to have the replacement product shipped as soon as possible.

CUSTOMER’S PREFERRED CARRIER

1. Customer files claim with carrier.

2. Customer  may  submit  a  replacement  purchase  order.  Customer  Service  will  work  with  production  facility  to  have  the

 

replacement product shipped as soon as possible.

3. If “lost” equipment is delivered at a later date and is not needed, VR will allow a Return to Stock without a restocking fee.

4. VR will NOT be responsible for any compensation when a customer chooses their own carrier.

RETURN SHIPPING

For the parts return procedure, please follow the instructions in the “General Returned Goods Policy” pages of the “Policies and

 

Literature” section of the Veeder-Root North American Red Jacket Mechanical Products Price Book.   Veeder-Root will not accept

 

any return product without a Return Goods Authorization (RGA) number clearly printed on the outside of the package.

RESPONSIBILITIES OF THE INSTALLER AND STATION OWNER

This installation, operation and service instruction manual shall be left with the owner of the service station at which this equipment

 

is installed. Retain these instructions for future use and provide them to persons servicing or removing this equipment.

 

ã Veeder-Root 2021. All rights reserved

.

Summary of Contents for TLS-350 Series






























Reviews: