background image

1

  Introduction

This manual contains installation procedures for the Veeder-Root Overfill Alarm and Acknowledgment (Ack) 

Switch. 

The Overfill Alarm unit contains:

• Red flashing light
• Alarm horn

The Acknowledgment Switch unit contains:

• ACKNOWLEGED light
• RESET push button 
• TEST push button 

Compatible Consoles

• TLS-3XX/4XX Series
• TLS-IB
• TLS-50
• TLS-HLD
• TLS2

Related Manuals

Depending on your installed console, you should reference the appropriate manuals below, to connect/setup the 

Overfill Alarm:
576013-879 TLS-3XX Series Site Prep Manual

576013-623 TLS-3XX Series Setup manual

577013-608 TLS-50 Site Prep manual

577013-609 TLS-50 Setup manual

577013-756 TLS2 Site Prep manual

577013-757 TLS2 Setup manual

577013-719 TLS-IB Site Prep manual

577013-785 TLS-HLD Setup manual

577013-784 TLS-HLD Site Prep manual

577013-879 TLS-4XX Site Prep Manual

Contractor Certification Requirements

Veeder-Root requires the following minimum training certifications for contractors who will install and setup the 

equipment discussed in this manual:

Service Technician Certification (Previously known as Level 2/3):

 Contractors holding valid Technician 

Certifications are approved to perform installation checkout, startup, programming and operations training, system 

tests, troubleshooting and servicing for all Veeder-Root Series Tank Monitoring Systems, including Line Leak 

Detection.

TLS-3xx Technician Certification:

 Contractors holding valid TLS-350 Technician Certifications are approved to 

perform installation checkout, startup, programming and operations training, troubleshooting and servicing for all 

Veeder-Root TLS-300 or TLS-350 Series Tank Monitoring Systems, including Line Leak Detection and associated 

accessories.

Summary of Contents for Overfill Alarm















Reviews: