background image

Assembly Instructions 

(cont.)

12.

 

Bolt the leg seat handle/strut/leg developer pivot assembly (K) to the leg/ab seat

bottom (M) (1/4-20 x 3/4 hex screws, qty 4). Attach this assembly to the leg/ab station (D)
such that the hooks on the end of the strut go into the rectangular hole on the top of the
column (D). Line up the 1/2" holes and insert the pivot (1/2" diameter rod and shaft retainers).
Install shaft retainer with a hammer. Bolt the ab seat back/preacher curl cushion (N) to
the leg/ab station (D) (1/4-20 x 3/4 hex screws, qty. 4). 

FIG. 7.

13.

 

Attach the leg developer (O) to the leg developer pivot assembly (K) (1/2-13x1

button head screw, qty. 2). Tighten very tight with 5/16" hex key. 

FIG. 7. 

Attach the cable

end to the leg developer (O), securing it with plastic hole-plug. 

FIG. 7A.

FIG. 7

M

K

N

D

O

23

14.

 

Attach the bench seat back (P) and bench seat bottom (Q) to the bench

(1/4-20 x 3/4 hex screw, qty. 10). The bench handle installs between cushion
(Q) and the bench frame and is held in place by 2 of these screws. Tighten
firmly. 

FIG. 8.

15.

 

Install right cross chest fly arm (arm closest to press station)

on pivot bar. The right arm is the one with the cam at the lowest point
on the arm. Install 1" washer and then cotter pin, bend end. Repeat this
process for the left arm. 

FIG. 9.

FIG. 7A

O

FIG. 8

P

Q

handle

FIG. 9

FR

ONT VIEW

LEFT

1" Washer

Cotter pin

RIGHT

1" Washer
Cotter pin

Summary of Contents for On-Line 1650










Reviews: