background image

FIGURE 4B 

- BULB REPLACEMENT

NOTE:

It is recommended that the unit be returned to Vector for replacement of the

spotlight  bulb. Contact Vector’s Technical Support Department at (954) 584-4446.

NOTE:

When handling a new halogen bulb, do not touch the glass portion of the bulb. 

Natural oils from your hands can cause the bulb to fail. If necessary, clean the bulb
with alcohol or a liquid window cleaner.

REPLACING THE AREA LIGHT BULB:

1. This 12volt 0.3 amp quartz halogen bulb is designed to last for the lifetime of

the product.

2.  In the event of failure, you may return the spotlight to Vector for bulb replacement.

Contact Vector’s Technical Support Department at (954) 584-4446.

8.

BATTERY

1.  The life expectancy of the 12 volt 3.0 Amp-hour, sealed lead-acid battery is

approximately 500 charging cycles. A replacement battery may be purchased
through the Vector Technical Support Department by calling (954) 584-4446

2.  A fully-charged battery will provide approximately 22 minutes of continuous light

from the spotlight, or up to16 hours of continuous light from the area utility light

3.  Do not allow battery to completely discharge, a dim light indicates that the 

battery charge is low, and should be recharged or powered from external 
DC source.  Charge battery as soon as possible after each use

REPLACING THE BATTERY PACK:

All lead acid batteries fail over time and with extreme temperature changes.
Keeping the battery charged periodically will extend battery life to the maximum.
Recharge after each use as soon as possible using AC/DC recharge adapter as
DC recharge methods may not fully recharge the battery to its full capacity. If the 
battery does not operate the spotlight for more than 10 minutes and recharge is 
sufficient to fully charge the battery, then it is time to replace the battery.

6

FIGURE 4B - 

XTREME SPORT SPOT BATTERY COMPARTMENT

1.

Disconnect the Xtreme Sport Spot

® 

2,000,000 from the charging/powering

source.

2.  Make sure the trigger switch is turned Off.
3.  Lift the battery pack cover and remove it.
4.  Carefully disconnect the positive and negative wires from the battery clips, 

noting the position of the wires. 

5.  Follow the directions to replace the quartz halogen bulb in the spotlight to gain

access to the battery from the inside of the spotlight body. 

6.  Push on the battery from the inside of the body to remove the battery. 
7.  Set the battery aside and insert the new battery from the rear of the body assembly.
8.  Reassemble the spotlight.
9.  Place the battery in the compartment taking care to MATCH UP THE PROPER

POLARITY - POSITIVE (red) to positive; negative (black) to negative.

10.

Attach wires to terminals.

11.  Make sure battery cover is properly aligned.
12.  Test the spotlight by operating the trigger switch. Charge the new battery for

18-20 hours using the AC/DC recharge Aadapter.

BATTERY DISPOSAL:

1. Non-spillable sealed lead-acid battery - This battery is fully recyclable and should

be accepted at any location that accepts common automotive starter batteries.
Examples of places that accept these batteries are: County or municipal recycling
drop-off centers, scrap metal dealers, and retailers who sell automotive replacement
lead acid starter batteries. For more information on recycling this battery, 
call toll-free (877) 288-7722.

2.  Before disposing of the battery, protect exposed terminals with heavy-duty tape

to prevent shorting (shorting can result in injury or fire).

3. Do not expose battery to fire or intense heat as it may explode.

FUSE REPLACEMENT:

The Xtreme Sport Spot

®

DC power/charging cord is equipped with a 10 amp 

cartridge fuse. If this fuse blows, there may be a short circuit in the power cord or
lamp assembly. The fuse will blow if the battery is connected with reverse polarity. The
fuse is accessed by unscrewing (counter-clockwise) the tip of the large DC plug. Check
the fuse with an ohmmeter or other continuity checker. If the fuse is open, investigate
why it blew and correct the problem before replacing the fuse. Reassemble the DC
connector and power the lamp from a 10 amp or greater 12 volt power supply.

5

    

      

BATTERY

BATTERY
COVER

BATTERY
CONNECTION

Summary of Contents for VEC142

Page 1: ...ble design The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period The customer is responsible for the shipping charges on all returned items after 30 days During the warranty period Vector Manufacturing Ltd will be responsible for the return shipping charges LIMITATIONS This warranty does not cover accessories bulbs fuses and batteries defects ...

Page 2: ... locked position simply rotate the thumbscrew counter clockwise to loosen Then position the swivel head in the desired position and tighten the thumbscrew to hold in place An additional benefit of the WorkLight is the utility value of the clamp and hook accessory Utilizing this accessory provides many mounting positioning options that can allow for hands free operation 2 1 IMPORTANT SAFETY INFORMA...

Page 3: ...er switch 1 The trigger switch is located on the front of the pistol grip handle of the spotlight see Figure 1 2 To turn the Xtreme Sport Spot 2 000 000 On squeeze the trigger switch 3 To turn the Xtreme Sport Spot 2 000 000 Off release the trigger switch 4 To lock the trigger switch into the on position for continuous operation squeeze the trigger switch and firmly press the trigger locking butto...

Page 4: ...ger switch is turned Off 3 Lift the battery pack cover and remove it 4 Carefully disconnect the positive and negative wires from the battery clips noting the position of the wires 5 Follow the directions to replace the quartz halogen bulb in the spotlight to gain access to the battery from the inside of the spotlight body 6 Push on the battery from the inside of the body to remove the battery 7 Se...

Reviews: