Vector START-IT 450 AMP JUMP-START SYSTEM Instruction Manual Download Page 5

4

IMPORTANT: 

This unit is delivered in a partially charged state. Fully charge unit with a household extension

cord (not supplied) for a full 48 hours before using for the first time. You cannot overcharge the unit using the
AC charging method.

• All On/Off switches should be in the OFF position when the unit is charging or not in use. Make sure all

switches are in the OFF position before connection to a power source or load.

• Do not use any accessory that is not recommended or provided by the manufacturer.
• This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6

volt or 24 volt battery system.

• This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a

vehicle that does not have a battery installed.

• Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the

recommended number of attempts, discontinue jump-start procedures and look for other problems that may
need to be corrected.

• Do not use this jump-starter on a watercraft. It is not qualified for marine applications.
• Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage,

use and recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct
sunlight, direct heat and/or moisture.

• Read And Understand This Instruction Manual Before Using This Unit.

SAVE THESE INSTRUCTIONS

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR THE START-IT

®

450 AMP JUMP-

START SYSTEM MODEL VEC012.

WARNING: TO REDUCE THE RISK OF INJURY:

• Follow these instructions and those published by the battery manufacturer and manufacturer of any equipment

you intend to use with this unit. Review cautionary markings on these products and on engine.

INTRODUCTION

Thank you for choosing the 

Start-It

®

450 Amp Jump-Start System

. This compact jump-starter is unique in the

amount of energy it can supply for its size. The internal battery is a high density sealed, lead-acid battery that
stores and delivers energy comparable to full sized ordinary jump-starters. Please read this guide carefully
before use to ensure optimum performance and avoid damage to the unit or items that you are using it with. 
The 

Start-It

®

450 Amp Jump-Start System 

is a compact, durable, portable jump-start system for vehicles that

have a standard 12 volt battery system. This self-contained, rechargeable system will start most vehicles
without the need for a host vehicle or 12 volt DC power supply.

FEATURES

• 450 instant starting amps
• Keyless ON/OFF Power Switch
• Built-in non-spillable, maintenance-free, heavy duty, 17 amp/hour, sealed, lead-acid battery
• Easy-to-read LED battery charge status indicators
• Reverse polarity connection warning indicator
• Cordless/rechargeable, includes 120 Volt AC Charging Adapter
• Requires no maintenance (other than recharging) for optimum operation
• Heavy duty cables and clamps
• Exclusive cable storage channels keep jumper cables out of the way until needed 

90527010 VEC012 EN SP.qxp:VEC012_ManualEN_090407  9/11/09  8:17 AM  Page 4

Summary of Contents for START-IT 450 AMP JUMP-START SYSTEM


















Reviews: