background image

Page 4 / 5

221031

    

Functions and Operations (continued)

● The shut-off delay is the length of time the light will stay at brightness after motion is detected. 

● You can set the shut-off delay by rotating the “TIME” Delay knob arrow so it points to the desired time setting (from 5 

   seconds to 3 minutes). To increase the shut-off delay, turn the knob clockwise. To decrease the shut-off delay, turn the

   knob counterclockwise.

Customization Options

Shut-off Delay

Notes:

1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. For best 

    performance, gently clean the lens with a soft cloth every 1 or 2 months to ensure maximum sensitivity.

2. For best performance, install fixture at least 8 feet above the ground. At such a height, the fixture will provide a 

    detection distance of up to 70 feet at 77 degrees Fahrenheit. (See Fig.6)

3. The sensor detects movement across a detection range of 180 degrees. (See Fig.7)

4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.8)

5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace 

    exhaust, or in a direction facing any reflective object or other nearby light source.

  

4. PC MODE (nighttime operation only)

    ● In "PC" mode, the light will turn on at full brightness at dusk and remains on until dawn.

5. 3 HOURS (3H) MODE (nighttime operation only)

    ● In “3H” mode, the light turns to high-level brightness at dusk, and stays on for 3 hours, then it turns to

       low-level 30% brightness. It turns to high-level brightness when motion is detected, and stays on as long as 

       motion continues. When motion is no longer detected, it remains on for the predetermined shut-off delay

       time you set (30s/1min/3min), then returns to the low-level 30% brightness automatically.

     ● The light turns off automatically at dawn.

6. Manual Override (nighttime operation only)

   

 ● To temporarily override the settings in 

“OFF” or “AUTO”

        or “3H” mode for on-demand continuous high-level 

        brightness at night, turn the wall switch OFF then turn it 

        ON twice within 3 seconds, the light remains on all night long.

        To shift back to “OFF” or “AUTO”  or “3H” mode, turn the wall

        switch OFF then turn it ON twice within 3 seconds again.

        (See Fig.6)

    ● The light turns off automatically at dawn.

    Note: To make sure the above functions operate properly,  

    always keep the wall switch in the ON position (including 

    the daytime).

       

Fig.6

“AUTO” “OFF” 

or “3H” Mode

 Manual

Override

Manual Override Operation Diagram

Turn wall switch OFF-ON-OFF-ON 

in 0.5~3 Seconds 

 

Turn wall switch OFF-ON-OFF-ON 

in 0.5~3 Seconds 

10'

8.0'

12.0'

70'

Where you install your fixture is important:

Be sure the light is mounted straight on the wall 

or eave; otherwise, the detection distance may 

be limited. 

Fig. 6

Fig. 7

Fig. 8

Motion

Least sensitive

Motion

Most sensitive

Sensor

180˚

Summary of Contents for T0692











Reviews: