background image

Page 3 / 5

221031

 

Sensor Adjustment Lower For Short Coverage

Sensor Adjustment Higher For Long Coverage

Fig. 5

Fig. 4

Fig. 2

Fig. 3

Adjusting the Light Head (B): 

2. 

Keep the light heads (B) 30˚ below horizontal to avoid water d

amage and electrical shock.

Sensitivity of Motion Sensor 

       ● You can adjust the sensitivity of the motion sensor b

y using the “SENS” knob located on the right 

           side of the bottom surface of the sensor. (See Fig. 4)

       ● Adjust motion sensor sensitivity to achieve desired performance.

       ● Approximate range for each setting from 10ft to 70ft.

 

1.Gently grasp the light heads (B) and tilt them left or right to adjust the light coverage area. Keep the light heads (B) at

   least 1” (25mm) away from the sensor.(See Fig. 5)

   

B

Functions and Operations

Choose a mode by sliding the switch on the bottom of the sensor of the fixture. (See Fig.4)

Note: When power is first applied, the light will be on and warm up lasts 30 seconds.

1. TEST MODE (daytime and nighttime operation.)

    ● Rotate “TIME” Delay knob arrow on the right side of the sensor head to the "Test" position. 

    ● The light turns to high-level brightness when motion is detected, and stays on as long as the motion continues.

       Then it reverts back to low-level 30% brightness about 5 seconds after motion is no longer detected.

2. OFF MODE (nighttime operation only)

    ● In "OFF" mode, slide the “TIME” Delay knob to the desired time(30s/1min/3min). At dusk, the light stays off,

       the light turns to high-level brightness when motion is detected, and stays on as long as motion continues. 

       When the motion is no longer detected, it remains on for the predetermined shut-off delay time you set 

       (30s/1min/3min), and then turns off automatically. 

    ● The light turns off automatically at dawn.

3. AUTO MODE (nighttime operation only)

    ● To “AUTO” mode, rotate “TIME” Delay knob to the desired time setting (30s/1min/3min). At dusk, the light turns on

       to low-level brightness. When motion is detected, the light turns to high-level brightness and stays on as long   

       as motion continues. When the motion is no longer detected, the light at high-level brightness remains on for 

       the predetermined time you set (30s/1min/3min), then switches back to low-level brightness automatically. 

    ● The light turns off automatically at dawn.

 

SENS

This side down

TIME

MODE

OFF AUTO

3H PC

3min           Test

1min           30s

Summary of Contents for T0692











Reviews: