Vaxcel T0274 Assembly And Installation Instructions Manual Download Page 8

Page 8 /  10

 

160826

12. Click fig.8 “Password” to set 

      a password for bluetooth

      device so that others need 

      password to connect this 

      lamp.

      

Fig. 12

Set password for light

Functions

Change image

Rename light

Password

Restore factory defaults

9:41 AM

100%

Setting 

Back

12. 1 The password must be 4 

          to 6 alpha-numberic 

          characters. Enter new 

          password and verify it 

          then press “Save”.

13. Click fig.8 “Restore factory 

      defaults” to restore your 

      settings (only the light name 

      and password) to the 

      original conditions.

13.1 Keep pressing the “reset” 

        button on the light for 5 

        seconds, the light will flash 

        three times. Then 

        press “Back” button.

Note: The photo’s settings 

          can’t be restored by 

          using this function.

Note: 1. Manual control and App control 

              independently.

          2. The function which is executed is the lastest 

               settings.

          3.  After a power cut or power outage, the 

               function of the light will revert back to the 

               actual settings of the switches on the fixture.

               App settings will also revert back to the factory 

               default.

          4.  For achieving the best performance,make 

               sure the wall switch is in “ON” state (daytime 

               and nighttime).

          

9:41 AM

100%

Enter new password

Verify password

(Must be 4 to 6 alpha-numberic characters)

Back

Save

Fig. 13

Fig. 13-1

Fig. 12-1

Restore factory defaults

Functions

Change image

Rename light

Password

Restore factory defaults

9:41 AM

100%

Setting 

Back

Restore factory defaults

Please press the reset button on the bottom

of sensor head for 5 seconds.

9:41 AM

100%

Back

Summary of Contents for T0274











Reviews: