Vaxcel F0097 Manual Download Page 9

PAGE: 9 / 10

 

 

Troubleshooting Guide

If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation 

or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any 

faults, please check this Troubleshooting Guide. If a problem cannot be remedied or you are 

experiencing difficulty in installation, please call our Customer Service Department (1-800-482-9235).

PROBLEM

1. If fan does not start:

2. If fan sounds noisy:

3. If fan wobbles:

4. If light does not work:

1. Check main and branch circuit fuses or circuit breakers.

2. Check line wire connections to fan and switch wire connections in switch

housing.

CAUTION: Make sure main power is turned off.

3. Make sure that the wall control is turned "ON".

1. Make sure all screws in motor housing are snug. (not too tight)

2. Make sure the screws which attach the fan blade bracket to the motor are tight.

3. Make sure wire connectors in switch housing are not rattling against each

other or against the interior wall of the switch housing.

CAUTION: Make sure main power is turned off before accessing switch 

housing.

4. Some fan motors are sensitive to signals from Solid State variable speed controls.

    DO NOT USE a Solid State variable speed control.

5. Allow "break-in" period of 24 hours. Most noises associated with a new fan will

   disappear after this period.

All blades are weighed and grouped by weight. Natural woods vary in density 

which could cause the fan to wobble even though all blades are weight-matched. 

The following procedures should eliminate most of the wobble. Check for wobble 

after each step.

1. Check that all blades are screwed firmly into blade brackets.

2. Check that all blade brackets are tightened securely to motor.

3. Make sure that canopy and mounting bracket are tightened securely to ceiling

junction box and junction box is mounted firmly to ceiling joist.

4. Most fan wobble problems are caused when blades are not equally level. To

check the blade levels, select a point on the ceiling above the tip of any blade.

Measure the distance from the ceiling to the blade tip, to an accuracy of 1/8

inch. Rotate the blades until the next blade is in the measuring position. Repeat

measurement for each blade. If all blade levels are not equal, you can adjust

blade levels by the following procedure. To adjust a blade tip down, insert a

washer (not supplied) between the blade and blade bracket at the screw

closest to the motor. To adjust a blade tip up, insert washer (not supplied)

between the blade and blade bracket at the two screws farthest from the motor.

5. If blade wobble is still noticeable, interchanging two adjacent (side by side)

blades can redistribute the weight and possibly result in smoother operation.

1. Check blue wire from fan to make sure it is connected to hot wire from house.

2. Check for loose or disconnected wires in fan switch housing.

3. Check for loose or disconnected wires in light kit.

4. Check for faulty LED module.

CAUTION: Make sure main power is turned off before accessing switch housing.

SUGGESTED  REMEDY

5. If fan and light kit

    do not work:

1. Replacing the battery.

2. Re-pair the transmitter and receiver by holding the " FAN OFF" button on

    the transmitter according to the manual.

230209

Summary of Contents for F0097











Reviews: