background image

13 

MAINTENANCE 

 

 

Properly maintained, your water heater can provide years of 

dependable, trouble free service. It is suggested that the 
purchaser follow the preventive maintenance program outlined 
below. 

A.  CONTROLS 

 

A periodic inspection of the operating controls, heating 
elements and wiring should be made by qualified service 
personnel. Temperature of the water should be tested 
periodically at the faucet to be sure thermostats are working 
properly. 

B.  LONG TERM SHUT DOWN 

 

If the water heater is to remain idle for an extended period of 
time, the power and water to the heater should be turned off 
to conserve energy. 

 

The water heater and piping should be drained, if they might 
be subjected to freezing temperatures. 

 

After a long shutdown period, qualified service personnel 
should check the heater’s operations and controls. 

 

Make certain the water heater is filled before placing it in 
operation. 

C.  DRAINING THE HEATER 

 

CAUTION: Shut off all power to the heater before 
draining water. To drain the tank, a hot water faucet must 
be opened to admit air to the tank. 

1.  Attach a hose to the drain valve on the heater. 
2.  Close valve on the cold water line to the heater. 
3.  Open the drain valve and direct the water to a drain. 

D.  EMERGENCY 

 

Should the heater be subject to flood, fire, or other damaging 
conditions, turn off the power and water to the heater. 

 

DO NOT

 place water heater in operation again until it has 

been thoroughly checked by qualified service personnel.  

 

 

Summary of Contents for Featherweight Series
































Reviews: