background image

Doc. # 01

-

04

-

033A

 

 

Glass Removal / Installation

 

There are three glass retainers. One on each side 
to square the glass to the rear seal and one in the 
front with special cams. The cams are used to 
gently push the glass back against the rear seal.

 

1)

 

Remove the cams and front retainer. Slide 
the glass towards the front to remove. 
Carefully set glass on a flat, protected 
surface. The cams are used to gently push 
the glass back against the rear seal.

 

2)

 

It is important to keep the inside of the 
cabinet clean. Vacuum out any loose debris 
from inside the cabinet. Refer to the replacing 
a light bar if needed.

 

3)

 

Reinstalling the glass.

 

Before installing the glass, switch the vacuum 
pump on and off to verify it is functioning 
properly. Clean both sides of the glass with 
glass cleaner and a lint free rag. Vacuum 
inside of cabinet. Position the glass seal side 
down, blue tape towards the front, on the 
front edge of the cabinet, and between the 
side retainers. Slide glass back until it 
contacts and it seated squarely against the 
back seal.  Place the front glass retainer and 
the three cams against the glass front. Install 
the screws but only snug the screws. Using a 
1/4” flat screw driver in the cam slots, rotate 
each cam to push the glass back. Do not 
over tighten the cams but apply enough 
pressure to make a seal. Now tighten the 
center screws. If the vacuum leaks, go back 
and tighten the cams a bit more.

 

4)

 

Inspection of LED light bars should be 
conducted monthly.  See page 11, Step 1,  
for instructions.

 

 

Inspection of UV Black bulbs should be 

 

conducted bi

-

monthly. See page 12, Step 1, 

 

for instructions

 

Note: The glass must be tight 
against the back glass seal in 
order to make a good vacuum. 
Special cams help to apply 
pressure.  Do not over tighten.

 

Wear gloves when handling the 
glass.  Glass is tempered and 
although strong, can shatter if the 
edges are subjected to an impact.

 

Do Not allow objects to 
contact the UV lights.

 

Maintenance

 

Side glass 
retainer

 

(1 each side)

 

Rear glass seal

 

Front glass retainer, 
with 3 cams.

 

Pg. 9

Summary of Contents for E-1000
















Reviews: