background image

OPERATION AND MAINTENANCE MANUAL 

MAC QM MOTORS 

 

 

 

 

 

 

 

 

 

 

 

PAGE: 17

 

 

 

                  

 

 

CODE: CTT42  EDITION: 01  RELEASE: JULY 2016 

Subject to technical changes without prior notice

 

 

3.3.5

 

Vibration grade 

 

The EN 60034-14 international standard specifies the factory acceptance vibration test procedures and vibration limits for certain 

electrical machines under specified conditions, when uncoupled from any load or prime mover.  

 

The standard defines two vibration grades: Grade ‘A’ (machines with no special vibration requirements); and Grade ‘B’ (machines 

with special vibration requirements).   
 

The  table  below  shows  the  limits of  maximum  vibration  magnitude  in  displacement,  velocity  and  acceleration  (RMS)  for  shaft 

height (H):  

  

Vibration 

grade 

Shaft height 

(mm) 

56 ≤ H ≤ 132 

132 

˂

 H ≤ 280 

˃

 280 

Mounting 

Displac. 

 µm 

Vel.   

mm/s 

Accel. 

m/s

2

 

Displac. 

 µm 

Vel.   

mm/s 

Accel. 

m/s

2

 

Displac. 

 µm 

Vel.  

mm/s 

Accel. 

m/s

2

 

Free suspension 

25 

1.6 

2.5 

35 

2.2 

3.5 

45 

2.8 

4.4 

Rigid mounting 

21 

1.3 

29 

1.8 

2.8 

37 

2.3 

3.6 

Free suspension 

11 

0.7 

1.1 

18 

1.1 

1.7 

29 

1.8 

2.8 

Rigid mounting 

  

  

  

14 

0.9 

1.4 

24 

1.5 

2.4 

Table 8: Limits of maximum vibration magnitude 

 

When no grade is specified, machines complying with this standard shall be grade “A”.

 

Summary of Contents for MAC QM

























































Reviews: