manualshive.com logo in svg

Varta element 12, Operating Manual

Share
Download
Varta element 12 Operating Manual Download Page 9

 

7 
 

General 

1

 

Information about this manual  

1.1

 

Symbol explanation 

The following types of safety directions and tips are used in this operating manual  

i 

Indicates tips regarding use of the device.

 

1.2

 

Safety instructions 

In this manual, the safety directions are structured as follows: 

 

 

Signal word 

Type and source of danger! 

Possible consequence(s) in the event of non-compliance. 

 

Measure and prohibitions to avoid the danger. 

1.2.1

 

Warning stages 

Signal word and warning colour identify the warning stage and provide an immediate indication of the type and 
severity of consequences if the measures to avoid the danger are not followed. 

Warning colour / signal word 

Consequences 

 

warns of a directly dangerous situation that can lead to death or to serious 
injuries and/or fire.  

 

DANGER 

 
 

warns of a possibly dangerous situation that can lead to death or to 
serious injuries and/or fire.  

 

WARNING 

 
 

warns of a possibly dangerous situation that can lead to light injuries 
and/or material damage.  

 

CAUTION 

 
 

warns of a possible situation that can lead to material and environmental 
damage and disrupt operations.  

ATTENTION 

 

 

 

Summary of Contents for element 12
















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands