Varta element 12 Operating Manual Download Page 101

Page: 101 / 111

13.10.9

Replacing and cleaning the air filter

•

Unscrew the filter holder.

Aid:

Torx 25 screwdriver

The air filter can be removed.

•

Clean the filter area with a cloth.

•

If necessary, clean the air filter with a vacuum cleaner.

•

Replace the air filter (at every second service) and screw the filter holder on.

Ensure that no dust from the air filter gets into the interior of the store.

Figure 17: Uninstalling the air filter (from front - bottom)

13.10.10

Dismounting the cover of the storage cabinet

The cover of the storage cabinet is connected to the storage cabinet with eight screws.

•

Loosen the fastening screws (5 x) on the front of the open storage cabinet.

Aid:

Torx 25 screwdriver

•

Loosen the fastening nuts (3 x) on the back of the storage cabinet.

Aid:

Open-end wrench no. 10

Figure 18: Cabinet cover nuts – (behind-bottom)

•

Remove the cover.

•

Remove the earth conductor from the earth lug on the cover interior.

Summary of Contents for element 12
















































































































Search results

Summary of Contents for element 12

Reviews:

Brands by name

Popular brands

Varta element 12, Operating Manual

Search results

Summary of Contents for element 12

Reviews:

Brands by name

Popular brands