background image

15 

 

Feature 09 – Floor Temp Limit: 

This function is available 

when mode 08 is set to 03 or 04. You can set a floor limiting 

temperature between 20-45°C (28°C is the default). 

 

Feature 10 – Optimum Start

: Optimum start will delay the 

start up of the heating system to the latest possible moment to 
avoid unnecessary heating, so that the dwelling is comfortably 
warm by the programmed time. The thermostat uses the rate of 
change (see below) setting to calculate how long the building 
needs to take to raise the building 1°C (With a rate of change 
of 20, the thermostat has calculated the building needs 20 

minutes to raise the building 1°C). On this thermostat, optimum 
start works on the Wake and Return comfort levels. 

 

Feature 11 - Rate of Change: 

For information only. 

 

Feature 12 - Weekday/Weekend or 7 Day Programming

The thermostat offers two programming methods. Weekday/ 
Weekend allows you to program 4 comfort levels for the 
weekday and 4 different comfort levels for the weekend. In 7 
day program mode, each day has 4 comfort levels that can be 
programmed independently. 

Summary of Contents for FH-01





















Reviews: