background image

VARI

LITE - VL3015 & VL3515 S

POT

 L

UMINAIRES

 S

ERVICE

 M

ANUAL

2 0

0 2 . 9 6 7 9 . 0 0 1 0   0

Troubleshooting Guide

If a problem is suspected, try recalibrating the luminaire to prompt an error message. Refer to 

“Error 

Messages - VL3015 Spot Luminaire” on page 18

 or 

“Error Messages - VL3515 Spot Luminaire” on 

page 19

 (depending on which product you have) for more information. The chart below provides 

possible causes and remedies for each message.

Table 2-3: Troubleshooting Guide 

Message

Symptom

Description

Possible Cause and Remedy

n/a

No response to DMX 

data

DMX Failure

MCB connector disconnected...

- check MCB DATA IN connection.

n/a

Lamp douses frequently

Lamp Douse

Fan failure...

- check fans for proper connection and 

operation.

n/a

Lamp will not strike

Lamp Strike Failure

Lamp cutout switch disengaged...

- check lamp cutout switches at lamp box 

and fan ducts.

Bad lamp...

- replace lamp.

Low input voltage...

- check input power (must be 200 to 264 VAC)

No Sens

No control, continuous 

recalibration, and/or 

mechanism at wrong 

position

Mechanism failed to find 

sensor (reported for Blue, 

Amber, Magenta, Col-

Wheel, CTO, Gobo1, 

Index1, Gobo2, Zoom and 

Edge)

Motor power not connected...

- connect motor power.

Sensor not connected...

- connect sensor.

Interconnect board not connected securely...

- check connection, inspect for bent pins.

Movement restricted or impeded...

- remove obstruction, check cable routing, 

and/or check voltage at MCB test point.

n/a

Luminaire does not 

power-up

No power

Not plugged in...

- ensure A/C cable is connected to power 

source.

- ensure A/C cable properly constructed.

Pan/

Encoder/

Fail

Luminaire will not pan

Pan Encoder Failure

MCB pan/tilt connector disconnected...

- connect MCB pan/tilt connector (J8).

Pan motor disconnected

- connect pan motor power.

Encoder faulty...

- replace pan end-of-travel/encoder sensor 

assembly.

Summary of Contents for VL3015



















































































































































































































Reviews: