Valtra VALMET 6000 Workshop Manual Download

Page: 346 / 1361

317

Model

Code

Page

1. 6. 1999

8450--8750

321

32. ACD power lift

1. 11. 1998

ACD: List of components

Sym---

Code

bol

Component

A1E

Autocontrol electronic unit

82D

A2E

Autocontrol, switch panel

83D

A3E

Compensator

82D

B1E

Position sensor, tractor

81D

B2E

Draft sensor, right

81D

B3E

Draft sensor, left

81D

(B4E) Position sensor, implement

81D

Speed sensor, gearbox

81D

(B10) Radar

81D

E1E

Illumination, switch panel

83D

E2E

Illumination, position control knob

83D

R1E

Potentiometer, position control

83D

S1E

Push button, mudguard, lifting, right

82D

S2E

Push button, mudguard, lowering, right

82D

S3E

Push button, mudguard, lifting, left

82D

S4E

Push button, mudguard, lowering, left

82D

S5E

Switch, cabin, lifting/lowering

82D

S7E

Switch, lowering speed

83D

S8E

Switch, transport height

83D

S9E

Switch, mixing/sensitivity

83D

S10E Autocontrol rocker switch, lift/stop/lower

83D

S11E Rocker switch, forced lowering

83D

S12E Switch, Drive Balance Control (+slip control) 83D

X1E

Connector, 9 pins, ACD sensors

X2E

Connector, 9 pins, supply, push buttons

Y1E

Solenoid valve, lowering

82D

Y2E

Solenoid valve, lifting

82D

Wire colours

Ru = brown

Pu = red

Ke = yellow

Si = blue

Mu = black

Vi = green

Va = white

Li = lilac

Connectors:

Connector X1E for the radar (B10), for the gearbox speed

sensor (B6) and for the possible position sensor on imple-

ment (B4E) are placed in the cab lever console. In addition,

the sensor B6 pins have connectors. The radar connector is

placed near the radar. The position sensor connector is

situated at the end of the sensor.

Connector X2E for supply and for the rear push buttons is

placed in the lever console. If the ACD does not respond

when the push buttons are used, check then fuse F11. If

the fuse is OK, check connector X2E (pin 1) and connector

X4 pin 8 in the fuse box. Also check the earth point GR4 in

the rear part of the lever console.

The wires from the LH side push buttons have been drawn

via connector X14 (in the lever console) and the wires of

the RH side push buttons have been drawn via connector

X12 (in the lever console).

If the ACD power lift responds to the push buttons, but

does not activate with the Autocontrol---switch (lift/stop/

lower switch), check the Autocontrol---switch and its wires.

If these are OK, but the ACD does not activate, the fault

may lie in the control unit box.

Note!

Summary of Contents for VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands

Valtra VALMET 6000, Workshop Manual

Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands