Valtra VALMET 6000 Workshop Manual Download

Page: 855 / 1361

802

Model

Code

Page

45. Final drives

6250--8950

450

1. 8. 2000

1. 11. 1998

HiTech

10---20 Nm

Picture 4.

Final drives 650 on 6250Hi ---8950Hi (---K36111) and 6600---8750 (J02316---K36111).

1. Grease nipple (greasing at every 1000 running hours)

2. Wind the wire ends one to one and a half turns and bend them

3. Bearing clearance is adjusted by tightening the centre bolt to 10---30 Nm. Apply Loctite 270 onto bolt threads.

5. Draining plug

6. Sealing compound Hylosil

7. Plastic ring in front of outer oil seal *)

*) In order to increase the oil volume (cooling advantage), the inner seal has been moved outwards. Axle housing, hub shaft and

the oil seal have different spare part numbers. The plastic ring is a new part.

Summary of Contents for VALMET 6000


















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands

Valtra VALMET 6000, Workshop Manual

Search results

Summary of Contents for VALMET 6000

Reviews:

Related manuals for VALMET 6000

Brands by name

Popular brands