background image

State of California. Proposition 65 Warning.

 Fuels used in gas, wood-burning or oil fired 

appliances, and the products of combustion of such fuels, contain chemicals known to the 

State of California to cause cancer, birth defects and other reproductive harm. 

California 

Health & Safety Code Sec. 25249.6.

Safety & Warning Information

State of Massachusetts Carbon Monoxide Detector/Vent Terminal Signage 

Requirements

For all side wall horizontally vented gas fueled equipment installed in every dwelling, 

building or structure used in whole or in part for residential purposes, including those owned 

or operated by the Commonwealth and where the side wall exhaust vent termination is less 

than seven (7) feet above finished grade in the area of the venting, including but not limited 

to decks and porches, the following requirements shall be satisfied: 

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of 

the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter 

shall observe that a hard wired carbon monoxide detector with an alarm and battery back-

up is installed on the floor level where the gas equipment is to be installed. In addition, the 

installing plumber or gasfitter shall observe that a battery operated or hard wired carbon 

monoxide detector with an alarm is installed on each additional level of the dwelling, 

building or structure served by the side wall horizontal vented gas fueled equipment. It 

shall be the responsibility of the property owner to secure the services of qualified licensed 

professionals for the installation of hard wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a 

crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery 

back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of 

completion of installation, the owner shall have a period of thirty (30) days to comply with 

the above requirements; provided, however, that during said thirty (30) day period, a battery 

operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as 

required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/

UL 2034 listed and IAS certified. 

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the 

exterior of the building at a minimum height of eight (8) feet above grade directly in line 

with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or 

equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS 

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas 

fueled equipment shall not approve the installation unless, upon inspection, the inspector 

observes carbon monoxide detectors and signage installed in accordance with the 
provisions of 248 CMR 5.08(2)(a)1 through 4.

 

Massachusetts

California

Summary of Contents for Madrona MF28EN








































Reviews: