background image

Safety & Warning Information

Children and adults should be 

ALERTED

 to the 

hazards of high surface temperature and should 

STAY AWAY

 to avoid burns or clothing ignition. Young 

children should be 

CAREFULLY

 

SUPERVISED

 when 

they are in the same room as the appliance.

DO NOT 

place furniture or any other combustible 

household objects within 36” of the fireplace front.

READ

 and 

UNDERSTAND

 all instructions carefully 

before starting the installation. 

FAILURE TO FOLLOW

 

these installation instructions may result in possible fire 

hazard and will void the warranty.

Prior to the first firing of the fireplace, 

READ

 the 

Owner’s Information section of this manual.

DO NOT USE 

this appliance if any part has been under 

water. Immediately, 

CALL

 a qualified service technician 

to inspect the unit and to replace any part of the control 

system and any gas control that has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be 

PERFORMED

 by a 

qualified service person. The appliance and venting 

system should be 

INSPECTED

 before initial use and at 

least annually by a professional service person. More 

frequent cleaning may be required due to excessive 

lint from carpeting, bedding, etc. It is 

IMPERATIVE

 that 

the unit’s control compartment, burner, and circulating 

air passageways 

BE KEPT CLEAN 

to provide for 

adequate combustion and ventilation air.

Always 

KEEP

 the appliance clear and free from 

combustible materials, gasoline, and other flammable 

vapors and liquids.

NEVER OBSTRUCT 

the flow of combustion and 

ventilation air. Keep the front of the appliance 

CLEAR

 

of all obstacles and materials for servicing and proper 

operation.
Due to the high temperature, the appliance should 

be 

LOCATED

 out of traffic areas and away from 

furniture and draperies. Clothing or flammable material 

SHOULD NOT BE PLACED 

on or near the appliance.

This unit MUST be used with a vent system as 

described in this installation manual. 

NO

 

OTHER

 vent 

system or components 

MAY BE USED

.

This gas fireplace and vent assembly 

MUST

 be vented 

directly to the outside and 

MUST

 

NEVER

 be attached 

to a chimney serving a separate solid fuel burning 

appliance. Each gas appliance 

MUST USE 

a separate 

vent system. Common vent systems are 

PROHIBITED

.

INSPECT

 the external vent cap on a regular basis to 

make sure that no debris, plants, trees, shrubs are 

interfering with the air flow.

The glass door assembly 

MUST

 be in place and sealed 

before the unit can be placed into safe operation.

DO NOT OPERATE

 this appliance with the glass door 

removed, cracked, or broken. Replacement of the glass 

door should be performed by a licensed or qualified 

service person. 

DO NOT

 strike or slam the glass door.

The glass door assembly 

SHALL ONLY 

be replaced 

as a complete unit, as supplied by the fireplace 

manufacturer. 

NO SUBSTITUTE

 material may be used.

DO NOT USE 

abrasive cleaners on the glass door 

assembly. 

DO NOT ATTEMPT

 to clean the glass door 

when it is hot.

TURN OFF

 the gas before servicing this appliance. 

It is recommended that a qualified service technician 

perform an appliance check-up at the beginning of 

each heating season.
Any safety screen or guard removed for servicing 

MUST BE REPLACED 

before operating this appliance.

BE CAREFUL

 not to put any decorating objects 

sensitive to heat on the stove or too close to the stove 

as it gets very hot when operating.

DO NOT 

use this heater as a temporary source of heat 

during construction.

NOTE:

 When operating your new fireplace for the first time, some vapors may be released due to the burning 

of curing compounds used in the manufacture of the appliance. They may cause a slight odor and could cause 

the flames to be the full height of the firebox, or even slightly higher, for the first few hours of operation. It is also 

possible that these vapors could set off any smoke detection alarms in the immediate vicinity. These vapors are 

quite normal on new appliances. We recommend opening a window to vent the room. After a few hours’ use, the 

vapors will have disappeared and the flames will be at their normal height.

Summary of Contents for Madrona MF28EN








































Reviews: