manualshive.com logo in svg

Valor L1 Series, Installation & Owner'S Manual

Share
Download
Valor L1 Series Installation & Owner'S Manual Download Page 44

44

QUALIFIED 
INSTALLER

Installation

 Install Driftwood Kit 1505DWK

Material required

•  Black steel platform (supplied with appliance)
•  Small container to distribute vermiculite (not included)
•  Driftwood Kit containing:

◊ 5 logs
◊ 6 pebbles
◊ 1 bag of vermiculite

Installation

Platform

Carefully unpack the kit.
1.  Install the steel platform around the burner as 

indicated. The openings in the platform should 
be underneath. Push the platform as far back as 
possible to maximize the air gap behind the burner.

2.  Fill a small container with the equivalent of 

approximately 3 cups (750 ml) of vermiculite from 
the bag supplied.

3.  Carefully spread the vermiculite on the surface of 

burner patting it gently with your hand to form a 
single layer to the approximate level of the top of 
the fl ange at the edge of the burner. Do not pour too 
much to avoid blocking the burner ports.

NOTE:

 Ensure the area within the pilot shield is 

clear of vermiculite.

Installed platform

Gap behind burner

Pilot shield

No gap in front of burner

Top view—platform

Summary of Contents for L1 Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands