manualshive.com logo in svg

Valor L1 Series, Installation & Owner'S Manual

Share
Download
Valor L1 Series Installation & Owner'S Manual Download Page 18

18

OWNER’S 
INFORMATION

Pilot Flame

Thermocouple Probe 
must be in Flame

1505DWK—Long Beach Driftwood

Pilot Flame can be seen 
between the front and 
rear left logs

1500DGM—Decorative Glass Murano

1500DGS—Decorative Glass

Pilot Flame can 
be seen left of 
the fi re bed

1514RSS—Rock & Shale

1500SWK—Split Wood

Pilot Flame can 

be seen left of 

the fi re bed

Pilot Flame can 

be seen left of 

the fi re bed

Checking Pilot and Burner Flames

A periodic check of the  pilot and burner fl ames should 
be made. Check after the fi re has been on for at least 
30 minutes. The pilot fl ame must cover the tip of the 
thermocouple probe. The main burner fl ame pattern will 
vary from appliance to appliance depending on the type 
of installation and climatic conditions.

The appliance area must always be kept clear and 
free from combustible materials, gasoline and other 
fl ammable vapors and liquids.
  Inspect the vent terminal outdoors regularly to make 
sure that snow, trees, bushes, leaves, or other objects 
do not obstruct it.
 Examine the vent system and terminal regularly. We 
recommend annually.

Maintaining Your Fireplace

Correct Flame Appearance

Summary of Contents for L1 Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands