manualshive.com logo in svg

Valor L1 Series, Installation & Owner'S Manual

Share
Download
Valor L1 Series Installation & Owner'S Manual Download Page 2

Massachusetts: The piping and fi nal 
gas connection must be performed by a 
licensed plumber or gas fi tter in the State of 
Massachusetts. Also, see Carbon Monoxide 
Detector requirements on page 63.

2

Designed and Manufactured by / for
Miles Industries Ltd.
 190–2255 Dollarton Highway, 
North Vancouver, BC, CANADA  V7H 3B1
Tel. 604-984-3496  Fax 604-984-0246
www.valorfi replaces.com

FOR THE OWNER

FOR THE QUALIFIED INSTALLER

The information contained in this installation manual is 
believed to be correct at the time of printing. Miles In-
dustries Ltd. reserves the right to change or modify any 
information or specifi cations without notice. Miles Indus-
tries Ltd. grants no warranty, implied or stated, for the 
installation or maintenance of your heater, and assumes 
no responsibility for any consequential damage(s).

Warranty Card at the 
back of this manual.

WARR

AN

TY

PR

OG

RAM

WARR

AN

TY

PR

OG

RAM

VA

LOR

CO M FO

R

T

VA

LOR

CO M FO

R

T

VA

LOR

CO M FO

R

T

Table of Contents

Safety and Your Fireplace ...................................... 3
Introduction ............................................................. 6

Locating Fireplace & Lighting Information Card ........ 6
Operating Your Fireplace for the First Time ............... 6

Operating Your Fireplace ....................................... 7

Fireplace Control Devices ......................................... 7
How to Turn Your Fireplace ON ................................. 7
How to Turn Your Fireplace OFF (and pilot) .............. 7
How to Ensure Your Fireplace Cannot 

Be Turned ON Inadvertently ................................... 7

Using the Remote Control ..................................... 8
Using the Wall Switch ..........................................13
Kits & Accessories ...............................................13
Lighting Instructions ............................................14
Maintaining Your Fireplace ..................................15

Servicing Your Fireplace .......................................... 15
Annual Inspection .................................................... 15
Cleaning Your Fireplace .......................................... 16
Checking Pilot and Burner Flames .......................... 18
Replacing Batteries ................................................. 19
Using Handset Wall Holder ...................................... 19

Warranty ................................................................65

Specifi cations .......................................................20
Overview................................................................21
Dimensions & Location ........................................22
Mantel & Hearth Clearances ................................23
Framing Requirements ........................................25
Venting ...................................................................29
Co-axial Venting....................................................30
Co-Linear Venting .................................................35
Installation Planning ............................................36

Plan Wall Finish ....................................................... 36

Installation .............................................................37

Unpack Appliance .................................................... 37
Fit Standoff s ............................................................38
Remove Heat Shield ................................................ 38
Convert from Top to Rear Outlet (if required) .......... 38
Fit optional LDK HeatShift Duct Kit’s take-off  collars 

to appliance (if used) ............................................ 38

Fit Appliance into Framing ....................................... 39
Complete Installation of optional LDK HeatShift 

Duct Kit (if used) ................................................... 39

Remove Window ..................................................... 39
Install Electrical Wiring (for optional accessories) ... 40
Set-up Gas Supply .................................................. 41
Install Liners ............................................................ 43
Install Driftwood Kit 1505DWK ................................ 44
Install Decorative Glass Murano 1500DGM ............ 46
Install Decorative Glass Set 1500DGS .................... 48
Install Rocks & Shale Set 1514RSS ........................ 50
Install Split Wood Kit 1500SWK .............................. 52
Refi t Window ........................................................... 55
Install Remote Battery and Wall Switch Kit 

RBWSK (required) ................................................ 56

Set-up Remote Control ............................................ 58
Check Operation ...................................................... 58
Install Trim and Barrier Screen ................................ 59
Install Remote Control Handset Wall Holder ........... 59

Wiring Diagram .....................................................60
Approved Venting Components ..........................61
Commonwealth of Massachusetts......................63
Warranty ................................................................65
Spare Parts............................................................66

© Copyright Miles Industries Ltd., 2018. All rights reserved.

Summary of Contents for L1 Series









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands