Valor L1 Series Installation & Owner'S Manual Download | Manualshive

Page: 1 / 72

background image

4005426-10

©2018, Miles Industries Ltd.

This appliance may be installed in an after-
market permanently located, manufactured
(mobile) home where not prohibited by local
codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certiﬁ ed kit is used.

HOT GLASS

WILL

CAUSE BURNS.

DO NOT TOUCH

GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

DANGER

!

A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.

Ce guide est disponible en français sur demande.

This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.

This appliance is suitable for installation in
a bedroom or bed sitting room.

INSTALLER

Leave this manual
with the appliance.

CONSUMER

Retain this manual
for future reference.

Please read this manual

BEFORE

installing and

operating this appliance.

INSTALLATION & OWNER’S MANUAL

— Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the
vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS

▪ Do not try to light any appliance.

▪ Do not touch any electrical switch; do

not use any phone in your building.

▪ Leave the building immediately.

▪ Immediately call your gas supplier from

a neighbor’s phone. Follow the gas
supplier’s instructions.

▪ If you cannot reach your gas supplier,

call the ﬁ re department.

— Installation and service must be

performed by a qualiﬁ ed installer,
service agency or the gas supplier.

!

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.

Direct Vent Zero Clearance Gas Fireplaces
1500JN (natural gas) & 1500JP (propane gas)

This manual contains instructions to install the

ENGINE ONLY.

A trim kit is

REQUIRED

to

complete the installation. A barrier screen is
provided with the trim kit.

Refer to the manual

supplied with the trim for installation.

L1 Series

1
2
3
...
»

Summary of Contents for L1 Series









































































Reviews:

No comments

Related manuals for L1 Series

Brand: Panasonic Pages: 2

Brand: Samsung Pages: 133

Brand: PACIFIC CYCLE Pages: 112

Brand: E+E Elektronik Pages: 14

Brand: E+E Elektronik Pages: 26

Brand: E+E Elektronik Pages: 28

Brand: E+E Elektronik Pages: 2

Brand: BW Pages: 8

EZ Link DAL 150

Brand: Harman Kardon Pages: 16

Brand: National Cycle Pages: 3

Brand: Carax Pages: 2

Brand: Lennox Hearth Products Pages: 24

FBL400RHA Series

Brand: Procom Pages: 23

Brand: Obelink Pages: 2

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: Home Accents Holiday Pages: 2

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands