12
Lighting Instructions
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a
fi
re or explosion may result
causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand or wall switch. Follow these instructions exactly. To
save gas, turn the pilot off when not using the appliance for a prolonged period of time.
B.
BEFORE LIGHTING
, smell all around the appliance area for gas. Be sure to smell next to the
fl
oor because
some gases are heavier than air and will settle on the
fl
oor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the
fi
re department.
C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by
hand, don’t try to repair them; call a quali
fi
ed service technician. Force or attempted repair may result in a
fi
re or
explosion.
D. Do not use this appliance if any part has been under water. Immediately call a quali
fi
ed service technician to
inspect the appliance and to replace any part of the control system and any gas control, which has been under water.
LIGHTING INSTRUCTIONS
1.
STOP!
Read the safety information above.
2.
TO CLEAR ANY GAS, turn main valve off by pressing ON/OFF on wall switch (1).
• Wait
fi
ve (5) minutes to clear out any gas, then smell for gas, including near the
fl
oor.
If you
smell gas, STOP!
Follow “B” in the safety information above on this label. If you don’t smell
gas, go to the next step.
3.
AUTOMATIC IGNITION:
MAN-knob (2) in ON position. Ensure Flame Adjustment
knob (3) is set to lowest setting (
)
(Fig. 1). Locate the pilot (Fig. 3.) inside of
fi
rebox at left hand side.
• On the wall switch, press the ON button; a short acoustic signal con
fi
rms the start
has begun.
• Further short acoustic signals indicate the ignition process is in progress.
• When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to
the highest setting.
• Press the small
fl
ame button (
) on the wall switch to reduce the
fl
ame height.
4.
MANUAL IGNITION:
MAN-knob (2) in MAN position
(Fig. 2). With the window
off, locate the pilot (Fig. 3) inside of
fi
rebox at left hand side.
• Set Flame Adjustment knob (3) to the lowest setting (
).
• Push down the metallic core (4) with a pen or similar instrument; this will establish
the pilot gas
fl
ow.
• Light gas at the pilot (5) with a match.
• Continue holding down metal core (4) for about 10 seconds; after release, pilot
should remain lit.
• If the pilot will not stay lit after several tries, turn the gas control knob (3) to OFF
(
) and call your local service technician or gas supplier.
• Reinstall the window and set the MAN-knob (2) to ON; turn Flame Adjustment knob (3) up (
) or down (
)
manually or use the
fl
ame buttons (
)(
) buttons on the wall switch to adjust the
fl
ame height.
TO TURN OFF GAS TO APPLIANCE
AUTOMATIC SHUT-OFF
(using the wall switch):
• Press and hold the small
fl
ame button (
) on the wall switch to shut-off the main burner gas
fl
ow.
• Press ON/OFF button on wall switch to shut-off the appliance, including pilot
fl
ame.
Spark
Pilot
Fig 3
5
Fig 1
Fig 2
1
OFF
OWNER’S
INFORMATION
Summary of Contents for 1500INO (NG)
Page 56: ......
