- 7 -
g
!
!
IMPORTANT! The battery-operated drill - screwdriver is sui-
table for drilling metal, wood, plastic and brick and for tightening
- loosening screws. It is prohibited to use dangerous materials in
environments with risk of fire/explosion.
These instructions contain information deemed necessary for proper
use, knowledge and standard tool maintenance. They do not include
information on drilling and screwing techniques; the user can find
additional information in specific books or publications or by attending
special training courses.
SYMBOLS
Carefully observe the symbols in
Fig.B
and memorise the respective
meaning. Correct interpretation of the symbols allows safer use of
the machine.
1 Type.
2 Technical data.
3 Lot number.
4 Trademarks of certifications.
V Volt
Hz Hertz
~
Alternating current
Direct current
A Ampere
W Watt
kg Kilograms
n
O
No-load speed
mm Millimetres
s Second
h Hour
min
-1
R.P.M.
dB Decibel
Double electric insulation
°C
Celsius degree
Li-Ion Lithium Ion
Wh Watt-hour
COMPONENTS
Refer to
Fig. A
and the following figures, attached to these instructions.
1 Start/stop switch and electronic speed modulator
2 Rotation direction and start lock switch
3 Rechargeable battery
4 Battery release buttons
5 Ring nut for tightening torque variation
6 Chuck
7 Light for work area
8 Main handle
9 Air vents
10 Switch of speed mechanical
11 Ring to hammer mechanism selection, drilling, tightening
12 Battery compartment
INSTALLATION
!
!
IMPORTANT! The manufacturer is not liable for any direct and/
or indirect damage caused by incorrect connections.
!
!
IMPORTANT! Before carrying out the following operations, make
sure that the battery is disconnected from the drill.
TRANSPORT
Always use the packaging or case (when provided) when transporting
the tool; this will protect it from impact, dust and humidity which can
compromise normal operation.
When transporting the tool remove the battery.
MOVING
Position the rotation direction switch in the middle position in order to
prevent accidental start-up.
Grip the tool by its handle and after use put it down upright without
banging using the base of the battery.
STARTING UP
When choosing where to use the electrical tool, the following should
be considered:
- that the place is not damp and is protected from the elements.
- that there should be a large operational area free from obstacles.
- that there is good lighting.
- that it needs to be used close to the general differential switch (for
the battery charger).
- that the power supply system is earthed and conforms to the stan-
dards (only if the electrical tool is class 1, which is equipped with a
plug with earth cable).
- that the room temperature should be between 10° and 35° C.
- that the environment is not in a flammable/explosive atmosphere.
Take out the machine and components and visually check that they
are perfectly intact.
BATTERY CHARGING (Follow the instructions attached to the charger)
!
!
IMPORTANT! Before using the drill it is necessary to fully charge
the battery.
!
!
IMPORTANT! Recharge only with the battery charger indicated
by the manufacturer. An inappropriate battery charger can cause
a fire hazard when used with other battery units.
In order to keep the battery efficient, do not fully discharge it.
Fully charging the battery:
- After every use.
- At least every 4 months, even in cases of disuse.
- If while working you notice a clear drop in the performance of the tool.
The factors that influence the battery lifetime are: number of charge/
empty cycles, stress from heavy use, time since it was manufactured,
lack of maintenance, absence of charging, permanence of temperatures
greater than 20°C.
INSERTING AND REMOVING THE BATTERY (fig.E)
- Insert the battery through the guides on the battery compartment.
(Pos.12)
- Remove the battery from the tool housing using the release device
(pos.4)
CUTTING TOOL ASSEMBLY (Fig.C)
!
!
IMPORTANT! During the assembly and disassembly of drills and
inserts, positioned centrally the selector of the direction of rotation
(Fig. A pos.2) so that it is prevented the actuation of the switch, and
then the unexpected startup.
!
!
IMPORTANT! Observe the Following instructions and ig.C:
Turn the ring nut
pos.1
to open and close the jaws holding back the
ring nut
pos.2
.
Check that the tip or the insert is centered and tightly fastened by the
chuck jaws.
