background image

12

-  Clean the tool using a cloth damped with hot water only.

-  Do not wet or spray water over the tool.

-  Do not use detergents or other solvents to clean the tool as 

you could irreparably damage it.  Chemical agents easily 

damage the plastic parts.

-  This tool does not require any particular maintenance as it 

has been lubricated using permanent greases. 

TROUBLE SHOOTING

 WARNING! UNPLUG THE TOOL FROM THE MAINS 

SOCKET BEFORE DOING ANYTHING.

If the jigsaw fails to start: check if all the electrical con-

nections are firmly plugged into the mains; check if the trip 

switch has tripped; check if a fuse has blown in your own 

electrical system, and that the brushes are not excessively 

worn. If the problem persists following these checks then 

the problem could be in the machine so have an authorised 

service centre check it.

STORAGE

Follow the tips below to store the tool:

1) 

Clean the tool and all its accessories thoroughly 

(see maintenance section).

2) 

Store the tool: 

  -  Out of reach of children.

  -  In a stable and safe position, 

  -  In a dry and cool place, 

  -  Avoid excessively high or low temperatures.

3) 

Protect the tool from direct light, if possible 

keeping it in the dark or semi-dark.

4) 

Do not close it in nylon bags where humidity 

could be produced

DEMOLITION

 Electric and electronic refuse may contain potentially 

hazardous substances for the environment and human 

health. It should therefore not be disposed of with domestic 

waste, but by means of differentiated collection at specific 

centres or returned to the retailer in the event of purchasing 

a new identical appliance. The illegal disposal of such 

equipment may result in prosecution to the full extent of 

the law.

WARRANTY

The product is legally protected against all non-

conformities with respect to its stated characteristics, as 

long as it is used solely for the purposes described in this 

user manual, that it has not been tampered with, that it has 

not been repaired by unauthorised personnel and, where 

necessary, only original spare parts have been used. 

Consumables and/or components subject to particular 

wear, such as batteries, bulbs, cutting and finishing 

elements, etc. are excluded from the guarantee.

Take the product to your retailer or an authorised service 

centre, exhibiting proof of purchase.

Amendments: the text and data correspond to the 

standard in place on the date of printing this manual. The 

manufacturer reserves the right to make changes to the 

product without notice in the case of technical, production 

or commercial requirements.

Take the product to your retailer or an authorised service 

centre, exhibiting proof of purchase.

Summary of Contents for 1411122-S550E





























Reviews: