Valet 551T Installation Manual Download Page 26

Page: 26 / 32

The learn routine will be exited if:

■

The ignition is turned on.

■

The Program switch is pressed too many times.

■

More than 25 seconds elapses between programming steps.

features menu

The factory default settings are indicated below in

bold

feature descriptions

1 ENGINE CHECK ON/OFF:

In the default setting the remote start will monitor either the vehicle's tach wire or

voltage depending on the programming of Feature 2. If programmed off, the vehicle will crank for the pro-

grammed crank time (Feature 5) and will not verify with tach or voltage that the vehicle is running. In the off

setting, if the vehicle fails to start, the ignition can stay on for the entire run duration. Using tach or voltage

check is always recommended if possible.

FEATURE
NUMBER

DEFAULT - LED ON SETTING

LED OFF SETTING

Engine checking on

Engine checking off

Tachometer checking type

Voltage checking type

12 minutes (1)* run time

24 minutes (2)*, 60 minutes (3) run time

Flashing parking light output

Constant parking light output

Cranking time 0.6 sec. (1)

Cranking time 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5),
1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec.

High voltage check level

Low voltage check level

Auxiliary output - factory alarm disarm

Auxiliary output - special accessory

Normal status output

Factory re-arm output

Activation pulses - 1 (1)

Activation pulses - 2 (2), 3 (3)

NOTE:

The numbers in parentheses indicate the number of times the LED will flash.

Summary of Contents for 551T

































Search results

Summary of Contents for 551T

Reviews:

Related manuals for 551T

Brands by name

Popular brands

Valet 551T, Installation Manual

Search results

Summary of Contents for 551T

Reviews:

Related manuals for 551T

Brands by name

Popular brands