Valet 551T Installation Manual Download | Manualshive

Page: 24 / 32

background image

24

© 2000 Directed Electronics, Inc.

internal programming jumper

Remove the control module case cover to access the jumper. In most cases, this jumper can be left in the OFF

position. Some new vehicles use less than 12 volts in their ignition systems. The unit may have trouble learning

the tach signal in these vehicles. Changing the jumper to the ON setting changes the trigger threshold of the

digital tach circuit so it will work properly with these vehicles. The vehicles affected include many newer

Dodge/Chrysler/Plymouth vehicles, such as the Neon, Cirrus, Stratus, Breeze and LH-based vehicles.

digital tach threshold on/off

«
...
22
23
24
25
26
...
»

Summary of Contents for 551T

































Reviews:

No comments

Related manuals for 551T

AutoCommand 20095

Brand: Directed Electronics Pages: 57

Brand: Manta Pages: 29

Brand: Bellman & Symfon Pages: 4

Brand: TFA Pages: 36

Brand: Argus Pages: 4

Brand: Audiovox Pages: 21

Brand: jablotron Pages: 2

Brand: Bellman & Symfon Pages: 27

Brand: Quell Pages: 2

Brand: Quell Pages: 17

Brand: Quell Pages: 20

Brand: iBeam Pages: 2

Brand: System Sensor Pages: 8

Brand: Greenheck Pages: 8

Brand: Eurotherm Pages: 140

Brand: Dometic Pages: 40

Brand: Family Gard Pages: 4

Brand: La Crosse Technology Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands