background image

Installation 

 

NOTE: Measure burner operating pressure at 

manifold test point with both burners 
operating at ‘Full’ setting. 

 

8. 

Verify operating pressure remains correct. 

 
 
 
 
 

Commissioning 

1. 

Before leaving the new installation; 

a.  Check the following functions in accordance with operating instructions specified in ‘Operation’ 

section of this manual. 



Light the Pilot Burner. 



Light the Main Burners. 



Check the Low Fire burner operation. 



Check the High Fire burner operation. 

 

b.  Ensure operator has been instructed in areas of correct lighting, operation, and shutdown 

procedure for appliance. 

 

2. 

This manual must be kept by owner for future reference, and a record of 

Date of Purchase, Date 

of Installation and Serial Number of Appliance recorded and kept with this manual. (These 

details can be found on Rating Plate attached to R/H inner side panel (refer to para-

graph ‘Gas Connection’ earlier in this section). 

 

NOTE:  If for some reason it is not possible to get appliance to operate correctly, shut ‘Off’ gas  

supply and contact supplier of this appliance. 

Pressure Test Point 

Low Fire Adjustment 

Fig 3 

Summary of Contents for GT8600G

























Reviews: