background image

4 Operation

10

Operating instructions atmoTEC exclusive, atmoTEC plus 0020214277_01

4.8

Setting the heating flow temperature (with
control)

E

bar

1

1.

Set the rotary knob for the heating flow temperature

(1)

to the clockwise end stop.

2.

Set the required heating flow temperature on the control
(

Control operating instructions).

4.9

Setting the heating flow temperature
(without control)

bar 

2

1

Set the target flow temperature on the rotary knob for
the heating flow temperature

(1)

in accordance with the

outdoor temperature.

Position

Meaning

Outdoor temperat-
ure

Fully left

Frost protection

Anti-clockwise (but
not at the end stop)

Transition Time

Approx.
10 … 20

(50.0 … 68.0

)

Centre

Moderate cold

Approx.
0 … 10

(32.0 … 50.0

)

Clockwise

Extreme cold

Below
0

(32.0

)

After turning the rotary knob for the heating flow tem-
perature, the display shows the set target flow tem-
perature

(2)

. After three seconds, this display goes

out and the default display reappears (current heating
flow temperature).

Note

The maximum heating flow temperature is set
in the factory at 75 °C. This can be defined by
the competent person to be between 40 °C
and 85 °C.

4.10

Setting the domestic hot water generation

4.10.1 Setting the domestic hot water temperature

Applicability:

Product with integrated domestic hot water generation

bar 

1

2

1.

Switch on the product (

"Switching on the product"

section).

2.

Set the rotary knob

(1)

for setting the domestic hot wa-

ter temperature to the required temperature.

Domestic hot water temperature: Left-hand stop
approx. 35 °C, right-hand stop max. 65 °C.

When setting the required temperature, the associ-
ated target value is shown in the display

(2)

. After

approx. five seconds, this display goes out and the
normal default display reappears (current flow tem-
perature of the heating installation).

Applicability:

Product with connected domestic hot water cylinder

Conditions

: Control connected

bar 

1

2

Switch on the product (

"Switching on the product"

section).

Set the domestic hot water rotary knob

(1)

as far as it

will go clockwise so that the control can work without
any faults occurring.

Danger!
Risk of death from legionella.

Legionella multiply at temperatures below
60 °C.

Summary of Contents for atmoTEC exclusive

















Reviews: