background image

Appendix

0020262548_00 Operating instructions

23

Setting level

Values

Unit

Increment, select

Default setting

Min.

Max.

Basic settings

Max. room air humidity

Max. room air hum.

30

70

%rel

1

40

Basic settings

Default setting

Time programmes

Yes

,

No

No

Everything

Yes

,

No

No

Installer level

Enter code

000

999

1

000

B

Troubleshooting

Symptom

Possible cause

Measure

Display remains dark

Software error

1.

Switch off the mains switch on all heat generators for approx.
1 minute and then switch them on again.

2.

If the fault persists, inform the competent person.

No changes in the display when
the rotary knob is turned

Software error

1.

Switch off the mains switch on all heat generators for approx.
1 minute and then switch them on again.

2.

If the fault persists, inform the competent person.

No changes in the display
when the selection buttons are
pressed

Software error

1.

Switch off the mains switch on all heat generators for approx.
1 minute and then switch them on again.

2.

If the fault persists, inform the competent person.

Display view:

Button lock act-

ive To unlock, press OK for
3 seconds

, it is not possible to

change the settings or values

Button lock is active

1.

If you would like to change any of the values, follow the in-
structions on the display.

2.

Also read through the

Button lock

Activate (

Page 13)

function.

Display view:

Restricted opera-

tion/ comfort protection

, insuf-

ficient heating up of the heating
and the domestic hot water

Heat pump does not work

1.

Inform the competent person.

2.

Select the setting for limp home mode until the competent
person arrives.

3.

To do this, read through the Implementing the setting when
the heat pump fails (

Page 17) function.

Display view:

Fault F. Fault:

Heat generator 1

, the specific

fault code (e.g. F.33) and the
specific heat generator appear
behind F. in the display

Heat generator faults

1.

Carry out a

Reset

fault message (

Page 17).

2.

If the fault persists, inform the competent person.

C

Maintenance messages

The maintenance message

Service heat pump 1

is an example of a maintenance message that may appear for heat pumps

1 to 7.

The maintenance message

Service heat generator 1

is an example of a maintenance message that may appear for heat

generators 1 to 7.

#

Message

Description

Maintenance work

Interval

1

Service heat
pump 1

The heat pump requires main-
tenance work.

Refer to the operating instruc-
tions of the relevant heat pump
for information on the mainten-
ance work required

See the operating instructions
for the heat pump

2

Service heat
generator 1

The heat generator requires
maintenance work.

Refer to the operating instruc-
tions of the relevant heat gener-
ator for information on the main-
tenance work required

See the operating instructions
for the heat generator

3

Low water pres-
sure

The water pressure is too low in
the heating installation.

Refer to the operating instruc-
tions for the relevant heat gen-
erator for information on filling
with water

See the operating instructions
for the heat generator

Summary of Contents for 0020236294





























Reviews: