Troubleshooting 6
0020262548_00 Operating instructions
17
5.4.6
Activating Cylinder boost
Op. mode
→
Cylinder boost
–
The
Cylinder boost
advanced function heats the water
in the domestic hot water cylinder until it reaches the set
desired temperature
Domestic hot water
.
The advanced function is active for one hour unless you can-
cel it sooner. The heating installation then returns to the pre-
set operating mode.
5.4.7
Activating System OFF active
Op. mode
→
System OFF active
–
The
System OFF active
advanced function switches off
the heating function, the domestic hot water circuit, the
circulation and the cooling. The frost protection function
is activated.
Ventilation is activated and works at the lowest ventilation
level.
The advanced function is deactivated by cancelling the ad-
vanced function. The heating installation will then return to
the pre-set mode.
5.5
Messages
5.5.1
Maintenance message
Maintenance messages (
→
Appendix C)
If maintenance is required, the system control displays a
maintenance message in the display.
To prevent the heating installation from breaking down and
to prevent damage, you must pay attention to the mainten-
ance message:
▶
Observe the operating instructions for the unit shown.
▶
Only carry out the maintenance instructions that are de-
scribed in the operating instructions for the unit shown.
▶
For all other maintenance instructions, inform the com-
petent person.
5.5.2
Fault message
Fault messages (
→
Appendix B)
A fault message with fault code (e.g. F.33) and the affected
heat generator appear in the system control's display.
▶
Press the
Reset
selection button.
–
Heat generator fault clearance?
appears in the
display.
▶
Press the
OK
selection button.
–
Faults are cleared for the heat generator
briefly
appears in the display.
▶
If the fault persists, inform the competent person.
If you would like to see the basic display on the display
again, press the left-hand selection button
Back
.
You can read the current fault messages under
Menu
→
In-
formation
→
System status
→
Fault status
. As soon as a
fault message occurs for the heating installation, the setting
level displays the value
Fault list
. The right-hand selection
button has been assigned the
Display
function.
6
Troubleshooting
Troubleshooting faults (
→
Appendix B)
6.1
Implementing the setting if the heat pump
fails
If the fault message
Restricted operation/ comfort pro-
tection Inactive
appears on the display, the heat pump has
failed and the system control enters limp home mode. The
back-up boiler now supplies the heating installation with
heating energy. During installation, the competent person
has restricted the temperature for limp home mode. You can
feel that the domestic hot water and heating are not becom-
ing very hot.
While you wait for the competent person to come, you can
use the rotary knob to implement the following settings:
Inactive
: The system control works in limp home mode;
heating and domestic hot water become moderately hot.
Heating
: The back-up boiler takes over the heating mode;
the heating becomes hot, the domestic hot water is cold.
DHW
: The back-up boiler takes over the domestic hot water
mode; the domestic hot water becomes hot, the heating is
cold.
DHW+heat.
: The back-up boiler takes over the heating and
domestic hot water mode; the heating and the domestic hot
water become hot.
The back-up boiler is not as efficient as the heat pump,
meaning that using only the back-up boiler to generate heat
is expensive.
If you want to implement settings on the system control, click
Back
and the basic display appears in the display. After five
minutes of no operation, the fault message appears again in
the display.
7
Care
7.1
Caring for the product
▶
Clean the casing with a damp cloth and a little solvent-
free soap.
▶
Do not use sprays, scouring agents, detergents, solvents
or cleaning agents that contain chlorine.
8
Decommissioning
8.1
Decommissioning the product
If you want to replace or remove the product, you must de-
commission the heating installation.
▶
This work should be carried out by a competent person.
Summary of Contents for 0020236294
Page 27: ......
