background image

2

  

3

Please read these instructions carefully before starting installation and keep for  

future reference.
Remove all packaging and check the product for missing parts or damage before 

starting installation.
Any alterations made to this product and fittings may infringe water regulations and 

will invalidate the guarantee.
The installation must comply with all Local/National Water Supply Authority 

Regulations/Byelaws and Building and Plumbing Regulations.  

To be installed in accordance with BS EN806.
We strongly recommend that you use a qualified and registered plumber.

General installation

Operating Specifications

Important - please read

Operating Pressure

Minimum operating pressure

 0.2 bar

 

(

1 bar

 if used as a bath fill)

 

Maximum operating pressure

 5 bar

This fitting is a mixing device and therefore water supplies should be reasonably 

balanced.
When installed, the fitting must comply with the requirements of the Water Supply 

(Water Fittings) Regulations 1999 and Scottish Byelaws 2004. 

For further information, contact the Water Regulations department of your local water 

supplier (see the WRAS website www.wras.co.uk for details) or the Water Regulations 
Advisory Scheme by email (info

@

wras.co.uk) or telephone: 01495848454.

Before making any inlet pipe connections, all supply pipes MUST be thoroughly flushed 

to remove debris. Failure to do so could result in damage or low flow from the mixer 

unit.
The fitting of isolating valves to the inlet feeds is advised for ease of maintenance.
Please take great care when installing this mixer not to damage its surface.
Please note if installing in an enclosed environment, access should be left for servicing 

and maintenance. No costs relating to inadequate access can be accepted.

Contents of Packaging

Installation guide &  

User manual

2 handle, 2 outlet thermostatic 

shower valve

TAB-148/2WO-NO

T-CP

Keep for future reference

Installation Guide

NOTION

WHERE

INSPIRATION

FLOWS

NOTION

2 handle, 2 outlet thermos

tatic shower valv

e

15

 ye

ar g

uarante

e

User Guide
Keep for future 

reference

Cover plate with  

Handset holder and outlet

Valve with 

Mortar guard

Handles with shrouds x 2

Spigot

Summary of Contents for NOTION TAB-148/2WO-NOT-CP









Reviews: