VADDIO WALLVIEW PRO Z700 WITH HSDS Installation And User Manual Download Page 11

 

WallVIEW PRO Z700 Installation and User Guide 341-674 Rev. B 

                                                                Page 11 of 12 

WARRANTY INFORMATION 

Hardware* Warranty - 

One year limited warranty on all parts. Vaddio warrants this product against defects 

in materials and workmanship for a period of one year from the day of purchase from Vaddio.  If Vaddio 
receives notice of such defects during the warranty period, they will, at their option, repair or replace 
products that prove to be defective.  
 

Exclusions 

- The above warranty shall not apply to defects resulting from: improper or inadequate 

maintenance by the customer, customer applied software or interfacing, unauthorized modifications or 
misuse, operation outside the normal environmental specifications for the product, use of the incorrect power 
supply, improper extension of the power supply cable or improper site operation and maintenance.  
 

Vaddio Customer service 

– Vaddio will test, repair, or replace the product or products without charge if the 

unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then 
repair the product or products. The cost of parts and labor charge will be estimated by a technician and 
confirmed by the customer prior to repair. All components must be returned for testing as a complete unit. 
Vaddio will not accept responsibility for shipment after it has left the premises.  
 

Vaddio Technical support 

- Vaddio technicians will determine and discuss with the customer the criteria for 

repair costs and/or replacement. Vaddio Technical Support can be contacted through one of the following 
resources: e-mail support at 

[email protected] 

or online at 

www.vaddio.com

.  

 

Return Material Authorization (RMA) number - 

Before returning a product for repair or replacement, 

request an RMA from Vaddio’s technical support. Provide a technician with a return phone number, e-mail 
address, shipping address, and product serial numbers and describe the reason for repairs or returns as well 
as the date of purchase and proof of purchase.  Include your assigned RMA number in all correspondence 
with Vaddio.  Write your assigned RMA number on the shipping label of the box when returning the product.  
Please see Vaddio’s website for current RMA policies and procedures.   
 

Voided warranty 

– The warranty does not apply if the original serial number has been removed or if the 

product has been disassembled or damaged through misuse, accident, modifications, or unauthorized repair.  
Cutting the power supply cable on the secondary side (low voltage side) to extend the power to the device 
(camera or controller) voids the warranty for that device.  
 

Shipping and handling 

- Vaddio will not pay for inbound shipping transportation or insurance charges or 

accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping, 
transportation, and insurance charges for all items under warranty but will not assume responsibility for loss 
and/or damage by the outbound freight carrier. If the return shipment appears damaged, retain the original 
boxes and packing material for inspection by the carrier.  Contact your carrier immediately. 
 

Products not under warranty 

- Payment arrangements are required before outbound shipment for all out of 

warranty products.  
 

*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry standard practices. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for WALLVIEW PRO Z700 WITH HSDS













Reviews: