background image

CeilingVIEW HD 

Vaddio CeilingVIEW HD CCU Installation and User Guide - Document 341-768 Rev. A 

Page 12 of 16

 

FCC, ICES-003 Compliance and CE Declaration of Conformity 

 
 
 

FCC Part 15 Compliance 

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to 
Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference in which case the user will be required to correct the 
interference at his/her own expense. 

 

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This 
device must accept any interference including interference that may cause undesired operation of the device. 
 
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void 
the user’s authority to operate this equipment. 
 
 
 

ICES-003 Compliance 

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set 
out in the Radio Interference Regulations of the Canadian Department of Communications.   
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux 
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par 
le ministère des Communications du Canada. 
 

 
 
European Compliance 

This product has been evaluated for Electromagnetic Compatibility under the standards for Emissions and 
Immunity and meets the requirements for E4 environment.  This product complies with Class A (E4 
environment). In a domestic environment this product may cause radio interference in which case the user 
may be required to take adequate measures. 
 

Standard(s) To Which Conformity Is Declared: 
EMC Directive

 89/336/EEC 

EN 55022A

  

 

Conducted and Radiated Emissions 

EN 55024 

 

Electromagnetic Compatibility - Immunity

 

EN 61000-4-2

    

Electrostatic Discharge Requirements 

EN 61000-4-3

    

Radiated Electromagnetic Field Requirement 

EN 61000-4-4

    

Electrical Fast Transients / Burst Requirements 

EN 61000-4-5 

    

Surge Requirements 

EN 61000-4-6

   

Conducted Immunity Requirements 

EN 61000-4-8

   

Power Frequency Magnetic Field Requirements 

EN 61000-4-11

   

Voltage Dips, Interrupts and Fluctuations Requirements 

 

 
 
 
 
 

Summary of Contents for CEILINGVIEW HD CCU

















Reviews: