vacuubrand PC 511 NT Instructions For Use Manual Download Page 48

Page: 48 / 63

page 48 of 63

Documents are only to be used and distributed completely and unchanged. It is strictly the users´ responsibility to check carefully

the validity of this document with respect to his product. Manual-no.: 999188 / 19/05/2009

☞

To connect a VMS Module A to a NT pumping unit remove

the plug at the lower side of the terminal box of the pump-

ing unit and connect pump using the connection cable IEC

plug- IEC socket to VMS.

Accessories

VMS module A

, 100-230 V, 3.5 A, CEE ........................................................................................

676001

VMS module A

, 100-230 V, 3.5 A, UK ..........................................................................................

676002

VMS module A

, 100-230 V, 3.5 A, CH ..........................................................................................

676003

VMS module A

, 100-230 V, 3.5 A, US ..........................................................................................

676004

The 2x5 pole connection cable and the country specific adapter cable (included in the VMS Module A

set) are not necessary for pumping units NT but:

VMS adapter cable

.......................................................................................................................

636655

(to connect Vacuum Management System VMS Module A to CVC 3000)

Connection cable

IEC plug- IEC socket ......................................................................................

636466

(to connect Vacuum Management System VMS Module A to NT pumping unit)

Vacuum gauge head VSK 3000

, capacitive Al

sensor 1080-0.1 mbar ...................................

636657

Coolant valve

VKW-B, 24 V= .......................................................................................................

674220

Air admittance valve

VBM-B / KF 16 / hose nozzle 6/10 mm, 24 V= ..........................................

674217

Y-type adapter

VACUU•BUS

........................................................................................................

636656

Extension cable

VACUU•BUS, 2m

.............................................................................................

612552

Wall bushing

VACUU•BUS

..........................................................................................................

636153

Cable RS 232C

, 9-pole, Sub-D .....................................................................................................

637837

Level sensor

(control of liquid level in catchpots) ......................................................................

699908

Exhaust waste vapour condenser Peltronic

.............................................................................

699905

Silencer

(with connection hose)....................................................................................................

636588

Upgrade kit SYNCHRO

to two inlets at PC 510/610 NT .............................................................

699920

Adapter

G 1/4 to PTFE tubing 10/8 mm, for inlet of PC 511/520/611/620 NT .............................

677060

Small flange KF DN 16

for assembly at inlet of PC 511/520/611/620 NT ..................................

662593

Seal ring

for small flange KF DN 16 (662593)............................................................................

3120565

Hose nozzle DN 6/10 mm

, for inlet at PC 511/520/611/620 NT ..................................................

642470

Modification kit for small flange KF DN 16

, at inlet of PC 510/610 NT .................................

699939

Hose nozzle DN 6/10 mm

, at inlet PC 510/610 NT .....................................................................

636635

Elbow piece (90°) for PTFE tubing

DN 10/8 mm, at inlet of PC 510/610 NT ............................

637873

Blind flange

(C1) for assembly at valve block or distribution head ..............................................

677136

Flow control diaphragm

(C2) for assembly at valve block or distribution head ..........................

677137

Solenoid operated valve

(C3-B) for assembly at valve block or distribution head ......................

636668

Manometer module

(C5) for assembly at valve block or distribution head ...................................

677100

PTFE tubing DN 10/8 mm

(sold by meter) ...................................................................................

638644

Attention

: Dust-laden gases, deposits and condensed solvent vapour can restrict air flow out the si

lencer. The resultant back pressure can lead to damage of pump bearings, diaphragms, and valves.

Under those conditions, a silencer must not be used.

Summary of Contents for PC 511 NT
































































Search results

Summary of Contents for PC 511 NT

Reviews:

Related manuals for PC 511 NT

Brands by name

Popular brands

vacuubrand PC 511 NT, Instructions For Use Manual

Search results

Summary of Contents for PC 511 NT

Reviews:

Related manuals for PC 511 NT

Brands by name

Popular brands