background image

Installation instructions

Heat pump dryer
One-family household

1068340-R02

22/05/2019

1068340-R02

1

For Service and Spare Part Information please contact: V-ZUG AUSTRALIA Pty. Ltd. Tel +61 7 3209 6822

The appliance should be installed by qualified personnel only.
Each step must be carried out and checked in full in the order specified.

Validity

The installation instructions apply to the models: 

12011

12013

Transport

Transport the appliance in an upright position only! Transporting it in any other position will result in damage to the
appliance! When carried carefully without being shaken, the appliance may be tilted a maximum of 90° to the left
(viewed from the front).

Identification plate

1

Open the appliance door.

The identification plate 

1

 is located

bottom right.

Supplied installation accessories

The necessary installation accessories are located in the washing drum and in the appliance packaging.

Designation

Article no.

Number

See installation step

Installation plate (incl. double-sided adhesive tape)

W40653

1

2. Positioning the installation plate

Tower panel

W55687

1

2. Positioning the installation plate

Condensate drain set (incl. screw material)

W56298

1

6. Connecting condensate drain

Room conditions/Ventilation

Keep all ventilation slits on the appliance clear and unobstructed. Otherwise an adequate supply of air is not guaran-
teed.

Ventilate the room well. Ensure that the temperature of the room is between 5–35 °C.

The room temperature must be kept between the range of 15–25 °C to ensure the economic running of the appliance.

Room size <10 m² (<20 m³)

Room size 

10 m² (

20 m³)

Room must be ventilated: There must be air inlet and outlet
openings to the adjacent room or to the outside, e.g. open win-
dow, ventilation grille or slits in the door, ventilation system.

Condensation may form on thermal bridges! The room must
therefore be aired after running several consecutive drying pro-
grammes, e.g. by opening a window or door to the room.

Summary of Contents for AT6TWHWR










Reviews: