Uwatec Galileo 2 User Manual Download Page 9 | Manualshive

Page: 9 / 96

background image

9

English

GALILEO 2 (G2) USER MANUAL

Charging will continue, but the above
display will switch off after 3 minutes.
When the battery is completely charged,
the following display will appear.

The G2 will alert you when the battery is
approaching a critical discharge level by
displaying the following message.

In addition, the battery icon with current
charging status is shown above the main
time-of-day display.

WARNING

Starting the dive with a weak battery may lead
to a situation where the G2 shuts off during
the dive. In case of such an event you should
always carry a backup instrument that will
enable you to complete the dive safely. If the
G2 switches off during a dive it will remain
locked in Gauge mode for 48 hours. (For more
information on Gauge mode operation, see
chapter:

Gauge mode

.)

F

NOTE: Storing the G2 with a low

battery may lead to a deep discharge
state, which shortens the life of the
battery.

WARNING

During the dive, when the battery charge level
indicator falls to only 1 segment, the display
will switch off automatically to save energy.
However, you can still check the display
manually by pressing the right button.

WARNING

The G2 will not start a dive when the battery
has reached the critical discharge level
indicated by the warning: “Charge battery!”
In this state you cannot use the G2 for diving.

«
...
7
8
9
10
11
...
»

Summary of Contents for Galileo 2

































































































Reviews:

No comments

Related manuals for Galileo 2

Brand: Panasonic Pages: 72

KW9M Eco-Power Meter

Brand: Panasonic Pages: 2

Brand: jenway Pages: 52

Brand: VELOCICALC Pages: 10

Brand: Hanna Instruments Pages: 28

Brand: ELGO Electronic Pages: 24

OPERA CONTROL CENTER SERVER - V 3.5

Brand: OPTICOM Pages: 21

DIRIS Digiware D-40

Brand: socomec Pages: 58

Brand: PCB Piezotronics Pages: 11

Brand: Ntron Pages: 29

Brand: Vectronics Pages: 2

Brand: Resol Pages: 24

Brand: B meters Pages: 3

Brand: SEAWARD Electronic Pages: 57

Brand: Trotec Pages: 3

Retinomax K+Screeen

Brand: Righton Pages: 112

Brand: R.M. Young Pages: 11

Brand: NARDA Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands