Uwatec Galileo 2 User Manual Download Page 83 | Manualshive

Page: 83 / 96

background image

83

English

GALILEO 2 (G2) USER MANUAL

4 .

G2 ACCESSORIES

4 .1 Bungee arm strap

Divers wearing thick neoprene wetsuits
or drysuits may prefer bungee mounting
instead of a standard arm strap. The G2 is
designed so that bungees can be affixed
at the corners of the device for maximum
stability.

The arm strap can be removed by pressing
the axle pins sideways through the bungee
rings.

F

NOTE:

Arm strap axle holes

in the housing are not symmetric!
When removing the arm strap axis,
place the pressing tool from the
smaller diameter side. Do not use the
opposite side bungee ring as support
when pressing the pin out.

4 .2 Wireless high pressure

transmitter

The G2 supports wireless tank pressure
using Smart series transmitters. With the
PMG function enabled you can use up to 8
transmitters with your G2.
Additional transmitters can be purchased
separately from your authorized
SCUBAPRO dealer.

F

NOTE: There are 3 generations of
Smart transmitters: Smart, Smart+
(longer distance) and Smart+ LED.
The G2 is compatible with all of these
versions.

4 .3 Skin temperature heart

rate belt

The new SCUBAPRO heart rate belt
features a patented skin temperature
measurement and transmission that is
supported by the G2.
The proper positioning for wearing a HR belt
is shown below. Adjust the strap so that it
is comfortable to wear but snug enough so
that it stays in place. When wearing a dive
suit the HR belt must be directly against the
skin. Moisten the electrode areas if your
skin is dry or when using a drysuit.

«
...
81
82
83
84
85
...
»

Summary of Contents for Galileo 2

































































































Reviews:

No comments

Related manuals for Galileo 2

Brand: ABB Pages: 8

TUNICS T100S-HP

Brand: Yenista Optics Pages: 66

Brand: Yamaha Pages: 2

Masoneilan 12400 Series

Brand: Baker Hughes Pages: 81

Brand: QLA Pages: 18

Brand: Callaway Pages: 11

Brand: VEE GEE Pages: 2

Brand: Kane Pages: 16

Brand: Kane Pages: 60

Brand: Olympus Pages: 4

Brand: Sensia Pages: 16

Brand: YOSensi Pages: 27

Brand: Rhosonics Pages: 65

Brand: LaserLiner Pages: 52

Brand: Laserworld Pages: 5

Brand: XS Instruments Pages: 41

Brand: HANLA Pages: 12

Brand: HyQuest Solutions Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands