Uwatec Aladin TEC 3H User Manuals Download Page 28 | Manualshive

Page: 28 / 79

background image

28

Functions during the dive

Decompression values

On entering the decompression phase, "NO STOP" disappears, the

STOP

DECO

symbol appears and an attention beep goes off. The nitrogen loading
bar stops flashing and the 6th segment lights up (red area). The deepest
decompression stage in metres (feet) is displayed and the decompression
stop duration of the displayed stage appears in minutes. The display "7:
3m (10ft)" means that a decompression stop of 7 minutes at a depth of 3m
(10ft) has to be made.

When a decompression stop has been completed, the next (shallower)
decompression stop is displayed. When all decompression stops have
been completed, the

STOP

DECO

symbol extinguishes, "NO STOP" and no-stop

time reappear.
Deco stop depths deeper than 27m (90ft) are displayed as " – – : – – ".

WARNING

The decompression alarm is activated if the decompression stop
is ignored. The arrow

STOP

DECO

, the decompression stop duration and

decompression stop depth begin to flash and an audible alarm
goes off. Due to the formation of microbubbles, decompression can
increase massively if a decompression stop is ignored. When the
surface is reached during the decompression alarm, the arrow

STOP

DECO

, the

decompression stop duration and decompression stop depth continue
flashing, in order to point to the risk of a decompression accident. The
SOS mode is activated 3 minutes after the dive if corrective action is
not taken (->17).
If the total (cumulative) duration of the decompression alarm is longer
than one minute, it is entered in the logbook.
Descend to the prescribed decompression stop depth immediately!

Total time of ascent

As soon as decompression stops are necessary Aladin TEC 3H shows the
total time of ascent. This includes the ascent time from the current depth to
the surface and all decompression stop obligations.

F

The total time of ascent is calculated on the basis of the prescribed

ascent rate. Total time of ascent can be subject to change if the
ascent rate is not ideal (100%).

Ascent time greater than 99 minutes is displayed as " – – ".

WARNING

On all dives with Aladin TEC 3H, make a safety stop for at least three
minutes at a depth of 5m (15ft).

4.4.12 Safety stop timer

The safety stop timer displays the time span a diver should spend at the
safety stop depth at the end of the dive. The timer is activated by the diver
and counts back from 3 minutes to zero. It can be restarted any number

Decompression

depth

Decompression

stop duration

Decompression obligation

Ignored decompression

alarm

Total ascent time

Minutes

Safety stop
icons

Seconds

Remaining
time span

«
...
26
27
28
29
30
...
»

Summary of Contents for Aladin TEC 3H
















































































Reviews:

No comments

Related manuals for Aladin TEC 3H

Masoneilan 12400 Series

Brand: Baker Hughes Pages: 81

Brand: Bacharach Pages: 19

Brand: Gardner Bender Pages: 4

Brand: GAPS Pages: 36

Brand: yellow jacket Pages: 26

Brand: Omano Pages: 14

VOLUTANK Petro 3003

Brand: Bartec Pages: 10

Brand: Prolude Amplification Pages: 15

Brand: Bogen Pages: 14

Brand: Kurzweil Pages: 12

Brand: PCE Instruments Pages: 6

Brand: Hanna Instruments Pages: 28

Brand: Kawai Pages: 2

QI-POWER-485-300-LV

Brand: QEED Pages: 2

Brand: Hammerhead Pages: 44

Brand: PCE Health and Fitness Pages: 66

Brand: J-TECH Pages: 3

Brand: SV Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands